background image

All written and visual data contained in this document reflects the latest product information available at the time of publication. 

Graco reserves the right to make changes at any time without notice.

Original instructions. This manual contains English. MM 334852

Graco Headquarters: 

Minneapolis

International Offices: 

Belgium, China, Japan, Korea

GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA

Copyright 2015, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.

www.graco.com

July 2019

Graco 7-Year Meter and Valve Warranty

Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in 
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended or limited warranty 
published by Graco, Graco will, for a period from the date of sale as defined in the table shown below, repair or replace equipment covered by this 
warranty and determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in 
accordance with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for, any malfunction, damage or wear caused by faulty installation, misapplication, 
abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor 
shall Graco be liable for malfunction, damage or wear caused by the incompatibility with Graco equipment of structures, accessories, equipment or 
materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment 
or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of 
the claim. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the 
original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be 
made at a reasonable charge, which charges may include the costs of parts, labor and transportation. 

Disclaimers and Limitations. The terms of this warranty constitute purchaser’s sole and exclusive remedy and are in lieu of any other warranties 
(express or implied), including warranty of merchantability or warranty of fitness for a particular purpose, and of any non-contractual liabilities, 
including product liabilities, based on negligence or strict liability. Every form of liability for direct, special or consequential damages or loss is 
expressly excluded and denied. In no case shall Graco’s liability exceed the amount of the purchase price. Any action for breach of warranty must 
be brought within eight (8) years of the date of sale, or two (2) years for all other parts.

Equipment not covered by Graco Warranty. Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a 
particular purpose, with respect to accessories, equipment, materials, or components sold but not manufactured by Graco. These items sold, but 
not manufactured by Graco (such as electric motor, switches, hose, etc.) are subject to the warranty, if any, of their manufacturer. Graco will 
provide purchaser with reasonable assistance in making any claim for breach of these warranties.

FOR GRACO CANADA CUSTOMERS

The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, 
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la 
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite 
de ou en rapport, directement ou indirectement, avec les procédures concernées.

Graco Information

For the latest information about Graco products, visi

www.graco.com

.

For patent information, see 

www.graco.com/patents

TO PLACE AN ORDER, 

contact your Graco distributor or call to identify the nearest distributor.

Phone: 

612-623-6928

 or Toll Free: 

1-800-533-9655,

   Fax: 

612-378-3590

Component

Warranty Period

Structural Components

7 years

Electronics (where applicable)

3 years

Wear Parts - included but not limited to o-rings, seals and valves

1 year

Содержание 24V553













Отзывы: