Graco 249512 Скачать руководство пользователя | Manualshive

Страница: 6 / 20

background image

Installation

6

311209W

Installation

NOTE:

Only connect to a Graco supply system with a

Graco heated fluid hose. See

Related Manuals

on

page 2.

Connect Heated Hose

1. An adapter may be required to connect the gun to

some hose sizes. If required, secure adapter onto

gun swivel (a) and tighten securely.

2. Securely connect hose to gun swivel (A).

3. Wrap connection with insulating cuff (B) (119889).

Connect Electrical Cable

1. Wrap hose cable around hose one time. Connect

electrical cable from hose to gun cable, engage

metal clip on top of connector.

2. Place flat side of cable connection against hose.

Make sure the metal clip faces away from the hose.

This will prevent damage to the hose from the clip

rubbing against it.

3. Fasten Velcro insulation wrap (198422) snugly

around the hose. Secure wrap with two Velcro

straps (198442) on the ends of the wrap.

Part

Adapter

Hose Size

120264

-8 JIC x -10 JIC

-8

- - - - -

Not Required

-10

120265

-10 JIC x -12 JIC -12

A

B

«
...
4
5
6
7
8
...
»

Содержание 249512





















Отзывы:

Нет отзывов

Похожие инструкции для 249512

Бренд: Omnia Страницы: 8

Бренд: Febco Страницы: 12

Бренд: Yetter Страницы: 16

Precision2 HP2 Series

Бренд: B-K lighting Страницы: 6

Бренд: Zero Hand Truck Страницы: 38

Бренд: B-K lighting Страницы: 3

Бренд: E-Z DRILL Страницы: 12

Бренд: e-survey Страницы: 54

Бренд: E-Pill Страницы: 8

XL-7 Command Station

Бренд: E-Mu Страницы: 22

Бренд: Gaspardo Страницы: 16

Бренд: Gastrodomus Страницы: 4

Бренд: HANYOUNG NUX Страницы: 2

Бренд: Gastrodomus Страницы: 39

Бренд: Taylor-Wharton Страницы: 25

Бренд: i-CAT Страницы: 96

Бренд: Rainin Instrument Страницы: 16

Бренд: Rain Harvesting Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды