background image

Technical Specifications

311209W

19

Technical Specifications

California Proposition 65

Hot Melt Dispense Guns

U.S.

Metric

Maximum operating temperature

400 °F 

204 °C

Maximum fluid working pressure

5000 psi

 34.5 MPa, 345 bar

Outlet port size

5/8-18 UNF-2B

Inlet port size on gun housing

7/8-14 UNF- 2B

Inlet port size on fluid swivel

7/8-14 JIC(m)

Voltage

230/240 Vac

Wattage

120 W

Resistance temperature detector 

(platinum RTD; 0.00385 ohm/ohm/°)

108.2 ohms @ 70 °F

108.2 ohms @ 21 °C

Heater resistance

Individually: 890 ohms, +/- 70 ohms

Wired in parallel: 445 ohms, +/- 35ohms

Weight

Without swivel: 2.7 lb

With swivel: 3.4 lb

Without swivel: 1.2 kg

With swivel: 1.5 kg

Dimensions

Height: 7.5 in.

Width: 3.0 in. 

Length: 

Models 249514 and 249515: 9.0 in. 

Models 249512 and 249513: 10.5 in.

Height: 191 mm

Width: 76 mm

Length: 

Models 249514 and 249515: 229 mm

Models 249512 and 249513: 267 mm

Wetted parts

Aluminum, fluorocarbon rubber, stainless steel, PTFE, carbon steel, brass

Notes:

All trademarks or registered trademarks are the property of their respective owners.

CALIFORNIA RESIDENTS

 WARNING:

 Cancer and reproductive harm – www.P65warnings.ca.gov.

Содержание 249512





















Отзывы: