Graco 249512 Скачать руководство пользователя

Страница: 13 / 20

Service

311209W

Inspection Frequency

Dispense Gun

Inspect the dispense gun at every use for leakage or

other visible damage.

Heater

Every two weeks, check the heater for proper resis

tance. Resistance should be approximately 890 ohms,

+/- 70 ohms for the 240V valves. Replace the heater

if necessary. See

Electrical Schematic

on page 12 for

test point.

Also inspect the heater when performing regular mainte

nance procedures.

Sensor

Every two weeks, check the sensor resistance. Resis

tance should be 108 ohms at 70° F (21° C). Replace the

sensor if necessary.

Also inspect the sensor when performing regular main

tenance procedures.

Adjust Needle Assembly

The trigger travel and corresponding valve opening are

factory set. To adjust this setting, use the following pro

cedure.

1. Follow the pressure relief procedure in your supply

system manual (

see

Related Manuals

on page 2

2. Disconnect from power source and wait for the unit

to cool.

3. Disconnect the gun from the hose.

4. Use a 11/32 in. wrench to loosen hex nut (4g).

5. Trigger the gun and use a 1/8 in. open-end wrench

on the flats of the needle to turn the needle (4a)

clockwise one turn as viewed from the handle end

of the gun.

6. Release the trigger; a slight free play of the trigger

handle should occur.

7. Repeat Step 4 until free play occurs.

8. Tighten hex nut (4g) to lock the adjustment.

Service Valve Stem and Seal

If fluid leaks past seal (4c), the seal or needle (4a) may

be worn or damaged. To replace the seal or valve stem,

use the following procedure:

1. Follow the Pressure Relief Procedure in your supply

system manual (see

Related Manuals

on page 2).

2. Disconnect from power source and wait for the unit

to cool.

3. Disconnect the gun from the hose.

4. Remove cover (16), and then slide the heater car

tridge and sensor cartridge out of body (2).

5. Loosen the needle nut.

6. Remove screws (33).

7. Unscrew the needle with the body from the yoke.

8. Remove the seal-cartridge assembly from the body

and replace seals and/or needle. Repack the

grease area of the packing nut prior to reassembly.

Reassemble in reverse order and follow

Adjust

Needle Assembly

Содержание 249512





















Результаты поиска

Содержание 249512

Отзывы:

Похожие инструкции для 249512

Бренды по названию

Популярные бренды

Graco 249512, Руководство по эксплуатации и запасным частям

Результаты поиска

Содержание 249512

Отзывы:

Похожие инструкции для 249512

Бренды по названию

Популярные бренды