background image

3 of 9

 

 

 
 

 

Your source for quality GNSS Networking 

(719) 561-9520

 

Solutions and Design Services, Now!

 

 

5/25/2007

 

       

Document number: 060-FSA-ABQ-AAS-AGZ

 

Rev.  001 

Functional Block Diagram 

Figure 1 below illustrates the functionality of the GPS Source S14WI GPS Splitter.  The S14WI 
consists of an RF Signal Processing System (illustrated in Blue), a DC Bias Select System 
(illustrated in Red), an Active GPS Antenna Monitoring System (illustrated in Green), and a 
Surge Arrestor System. 
 

DC Switching Circuit

S14WI GPS Signal Splitter

RF In,

DC Out

RF Out,

DC In 

RF Out,

DC In 

RF Out,

DC In 

RF Out,

DC In 

RF Choke

RF Choke

RF Choke

RF Choke

RF Choke

DC Blk.

DC Blk.

DC Blk.

DC Blk.

DC Blk.

Pwr.

Supply

Active

or

 Passive

Active GPS Antenna 

Monitoring System

 

 

Figure 1  S14WI Functional Block Diagram

 

 

 

Operational Description  

RF Signal Processing System 

 
The RF signal processing system consists fundamentally of three classical Wilkinson Splitter 
elements that divide the RF signal from the antenna input evenly between four RF output ports.   
 
There are several options that are available concerning the RF Signal Processing System.  
These options are: 
 

Содержание S14W










Отзывы: