background image

13

For  warranty  consideration,  parts  or  other  service  informa-

tion, please contact your local distributor. If you need further 

assistance, contact the GPI Customer Service Department in 

Wichita, Kansas, during normal business hours.
A toll free number is provided for your convenience.

1-800-835-0113

To obtain prompt, efficient service, always be prepared with the 

following information:
•  The model number of your pump
•  The serial number or manufacturing date code of your pump
•  Parts descriptions and numbers
Part information can be obtained from the Illustrated Parts List.
For warranty work, always be prepared with your original sales 

slip or other evidence of purchase date.
Please contact GPI before returning any parts. It may be possible 

to diagnose the trouble and identify needed parts in a telephone 

call. GPI can also inform you of any special requirements you will 

need to follow for transportation and handling of fluid equipment.

Do not return the pump or parts without authority from the 

Customer  Service  Department.  Due  to  strict  government 

regulations, GPI cannot accept parts unless they have been 

drained and cleaned.

SERVICE

CAUTION

Содержание P-120DEF

















Отзывы: