Goulds Pumps GSP Series Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 28

background image

4

Safety

It is extremely important that you read, understand, and follow the safety messages
and regulations carefully before handling an ITT product. They are published to help
prevent
• personal accidents and health problems
• damage to the product
• product malfunction
Observe all safety messages highlighted in other sections of this manual.
A pump is a pressure-containing device with rotating parts that can be dangerous.

Caution: You must observe the instructions for installation, operation, and

maintenance contained in this manual. Failure to do so could result in physical
injury, damage, or delays.

Safety message levels

Table 1: Definitions
Safety message level

Indication

Danger:

Indicates a hazardous situation which, if not

avoided, will result in death or serious injury.

Warning:

Indicates a hazardous situation which, if not

avoided, could result in death or serious injury.

Caution:

Indicates a hazardous situation which, if not

avoided, could result in minor or moderate injury.

Note:

Indicates a potential situation which, if not avoided,

may result in undesirable results or state. Indicates a

practice not related to personal injury.

Electrical Hazard:

Indicates the possibility of electrical risks if

direction are not applied in a proper manner.

Environmental safety

Preventive measures for the working area

Always keep the pump station clean to avoid and/or discover emissions.

Recycling guidelines

Always recycle according to the guidelines listed below:
1. Follow local laws and regulations regarding recycling if the unit or parts are accepted
  by an authorized recycling company.
2. If the first guideline is not applicable then return the unit or parts to the nearest
  ITT representative.

Waste and emissions

Observe these safety regulations regarding waste and emissions:
• Dispose appropriately of all waste.

•  Handle and dispose of the pumpage in compliance with applicable environmental
  regulations.
•  Clean-up all spills in accordance with safety and environmental procedures.
•  Report all environmental emissions to the appropriate authorities.

«
...
2
3
4
5
6
...
»

Содержание GSP Series





























Отзывы:

Нет отзывов

Похожие инструкции для GSP Series

Altherma 3 H MT ECH2O

Бренд: Daikin Страницы: 24

Altherma 3 H MT ECH2O

Бренд: Daikin Страницы: 68

Бренд: Daikin Страницы: 46

Бренд: Daikin Страницы: 24

Бренд: Davey Страницы: 16

Water Solutions 3098 Series

Бренд: Zoeller Страницы: 4

Aquanot Spin 508

Бренд: Zoeller Страницы: 2

Бренд: Zoeller Страницы: 11

Бренд: Zip Страницы: 18

Nessie Plug&Spray NPS 1CS

Бренд: Danfoss Страницы: 12

WELCH DUOSEAL 1397C-46

Бренд: Gardner Denver Страницы: 28

Бренд: Jecod Страницы: 3

BEST ONE Series

Бренд: EBARA Страницы: 7

Бренд: Rinnai Страницы: 2

Бренд: Trane Страницы: 8

Бренд: Viessmann Страницы: 52

GOULDS e-SVI Series

Бренд: Xylem Страницы: 40

Gyre 300 Series

Бренд: Maxspect Страницы: 164

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды