Gossen MetraWatt P1500, Руководство по эксплуатации

Страница: 59 / 72

GMC-I Messtechnik GmbH 59
Abbreviating commands : Abbreviated commands are identified with boldface letters. Letters not printed in boldface can be omitted. Example: “ OU TPUT ON” = “OU ON”
As a rule, letters can be entered in upper or lower case.
Stringing commands together : Several commands is a single data string must be separated by semicolons (;). Example: “USET 12; ISET 8.5; OUTPUT ON”
Formats for numeric parameters: m, n: Whole number (integer);
w: Whole number, fixed or floating decimal point number with or without exponent. Examples: “12.5”, “0012.5”, “1.25E1”, “+1.25 e+01”
* /15 or /1700, respectively as from firmware version 004
Devise-Specific Settings
ADJ UST
(CAL)
txt(,w) Balancing/calibration function UOFF / UFS / IOFF / IFS / (EXIT), 0

w

respective balancing limit.
The specified order for the procedure must be adhered to!
“EXIT”

UNCAL, abort with error message
— X X
ANA LOG_IN txt1,txt2 Connection of analog control inputs U(Uext), U(Iext) OFF / ON / SSET OFF X X
C_D YN txt Setting for current regulating dynamics R / L R X X
DI SPLAY txt1,txt2 Digital display function switching txt1: ON / OFF / UO /US / PS
txt2: ON / OFF / IO / IS / PO UO
IO X X
FS ET txt Sequence function parameter CLR / NF / RU / RI / SOFF / S_ON / AUOF / AUON / AUSS / AIOF /
AION / AISS / R01 ... R12/15* / S01 ... S12/15* CLR X X
IL_H ( ILI M) w Upper limit value for current setting Iset

w

Inom [A] Inom X X
IL_L w Lower limit value for current setting 0

w

Iset [A] 0 X X
IS ET w Current setpoint [A] IL_L

w

IL_H [A] 0 X X
MEAS_LP F txt Low-pass filter for measured value acquisition 1 / 2 / 3 / 4 3 X X
MI NMAX txt Min-max storage for measured U and I values OFF / ON / RST
“ON”

enable tolerance band function for CRB.0/1, ERC.0/1, SIGx_OUT
OFF X X
OC_D ELAY w Overcurrent protection triggering delay 0.000

w

65.535 [s] 0 X X
OCP txt Overcurrent protection OFF / ON / R01

R12/15* OFF X X
OCS ET w Overcurrent protection trigger value OCSETmin (3) [A]

w

OCSETmax (80 A) [A] 80 A X X
OU TPUT txt Switch power output on and off OFF/ ON OFF X X
OV_D ELAY w Overvoltage protection triggering delay 0.000

w

65.535 [s] 0 X X
OVP txt Overvoltage protection OFF / ON / R01

R12/15* ON X X
OVS ET w Overvoltage protection trigger value 3 [V]

w

OVSETmax (80 V) [V] 80 V X X
POW ER_ON txt Response after power on RST / SBY / RCL / R01

R12/15* RST X X
PS ET w Power setpoint [W] 0

w

Pnom (1500, 3000, 4500) [W] (PSET = PNOM)

P-REG. OFF) Pnom X X
RE PETITION n(,i) Number of repetitions for sequence function 0

n

255; 0 means continuous repetition.
i is an optional parameter for the setup memory location (1 through
12/15), which should be written directly with REPETITION.
0 X X
SEQ UENCE txt(,n) SEQUENCE control command OFF / GO / HOLD / CONT(,n) / STRT / STEP (,n) / BSTP / STOP / ESC
n is an optional parameter from start address to stop address — X X
SIG 123 txt1,txt2,txt3 Analog interface signal outputs OFF / ON / OUT / MODE / SEQ / SSET / U_LO / U_HI / I_LO / I_HI OFF X X
SINK txt Sink function on/off OFF / ON ON X X
SM_L OAD n Load sequence memory location
USET,ISET,TSET,FSET 1

n

1536/1700* — X X
SM_S TORE n Write current USET,ISET,TSET,FSET to sequence
memory location 1

n

1536/1700*
n = 0: clear contents from start to stop address
— X X
SS ET txt Command for an assigned switching function OFF / ON OFF X X
STA RT_STOP m,n(,i) Start and stop address 1

n1

n2

1536/1700*
i is an optional parameter for the setup memory location (1 through
12/15), which should be written directly with START_STOP.
1.1 X X
STO RE n,w1,w2,w3,txt Transfer parameters directly to memory 1

n

1536/1700* , memory location address
0

w1

Unom [V]
0

w2

Inom [V]
0

w3

65.535 [s], 0 means Tdef
txt, see “FSET”
— X X
T_M ODE txt1,txt2 Function selection for trigger inputs OFF / OUT / SQS / SEQ(,n) / LLO / MIN (,n) / AIX / AIU / AII OFF X X
TD EF w(,i) Default time rate for SEQUENCE function 0.001

w

65.535 [s]
i is an optional parameter for the setup memory location (1 through
12/15*), which should be written directly with TDEF.
0.001 X X
TIME DATE txt Set system clock (RTC) yyyy-mm-ddThh:mm:ss unv X X
TS ET w Memory location-specific dwell time for sequence
function 0.000 = Tdef, 0.001

w

65.535 [s] 0.000 X X
UI _C_SET w1,w2,w3,w4 Reference values for Uout/Iout, tolerance band
function w1, w2: 0

w1 < w2

Unom [V]
w3, w4: 0

w3 < w4

Inom [A]
0,Unom,
0, Inom X X
UL_H ( ULI M) w Upper limit value for voltage setting Uset

w

Unom [V] Unom X X
UL_L w Lower limit value for voltage setting 0

w

Uset [V] 0 X X
US ET w Voltage setpoint [V] UL_L

w

UL_H [V] 0 X X
WA IT w Additional waiting time 0.001

w

65.535 [s] — X
Setting
Command Parameter Meaning Value Range / Selection
De
fa
ul
t
Set
tin
g Afte
r
RE
SET
*RS
T
Manual Re
m
o
te