Gossen MetraWatt KONSTANTER SPL Series, Руководство по программированию

Страница: 6 / 16

6 GMC-I Messtechnik GmbH
2.2 SCPI Root Commands
2.2.1 ABORt
This command cancels all pending [:LEVel]:TRIG operations (such
as CURR:TRIG). As a result, subsequent triggers have no effect
on the input level. ABORt has no effect on the Transient operation
and List (Sequence) operation.
Command Syntax: ABORt
Parameter: None
Example: ABOR
Query Syntax: None
Related Commands: CURR[:LEVel]:TRIG, VOLT[:LEVel]:TRIG,
RES[:LEV]:TRIG, STAT:OPER:COND?
2.2.2 CURRent Subsystem
[SOURce:]CURRent[:LEVel] [:IMMediate] [:AMPLitude]
Specifies the immediate current level for the load. CURR? MIN
and CURR? MAX return the maximum and minimum current level
for the present range. If the set level exceeds the range, an error
will be generated.
Command Syntax: [SOURce:]CURRent [:LEVel] [:IMMediate]
<NRf+>
Parameters: Digits |MIN|MAX
Unit: A|mA
Example: CURR 25A
Query Syntax: [SOURce:]CURRent[:LEVel] [:IMMediate] [:AMPLitude]?
Parameter: None |MIN|MAX
Example: CURR? CURR? MIN CURR? MAX
Returned Parameter: <NR3>
Related Commands: CURR:LOW; CURR:TRIG, CURR:RISE:RATE
[SOURce:]CURRent[:LEVeI]:TRIGgered [:AMPLitude]
Specifies the current trigger level for the load. It shares the same
current range with the immediate current. The current trigger level
becomes the immediate current level only when the trigger signal
has been received.
Command Syntax: [SOURce:]CURRent [:LEVel]:TRIGgered [:AMPLitude]
<NRf+>
Parameter: Digits |MIN|MAX
Unit: A|mA
Example: CURR:TRIG 5A CURR:TRIG 50mA
Query Syntax: [SOURce:]CURRent[:LEVeI]:TRIGgered [:AMPLitude]?
Parameter: None |MIN|MAX
Example: CURR:TRIG? CURR:TRIG? MIN CURR:TRIG? MAX
Returned Parameter: <NR3>
Related Commands: INIT, INIT:CONT
[SOURce:]CURRent:PROTection[:LEVel]
Specifies the current limit at which software protection occurs.
The current limit range is 0-30 A respective 0-40 A. When the cur-
rent protection is enabled, the actual current exceeds or equals to
the current limit for software protection, and the load enters into
the current protection status. When the input current reaches the
current limit for the specified delay period, the load input is turned
off.
Command Syntax: [SOURce:]CURRent:PROTection[:LEVel]
<NRf+>
Parameter: Digits |MIN|MAX
Unit: A|mA
Example: CURR:PROT 15A
Query Syntax: [SOURce:]CURRent:PROTection[:LEVel]?
Parameter: None |MIN|MAX
Example: CURR:PROT? CURR:PROT? MIN CURR:PROT? MAX
Returned Parameter: <NR3>
Related Commands: CURR:PROT:STAT, CURR:PROT:DEL,
INP:PROT:CLE
[SOURce:]CURRent:PROTection:DELay
Specifies time for which protection current limit may be exceeded.
The delay period is calculated after the actual current reaches or
exceeds the protection current limit. When the delay period is
reached, the load input will be turned off.
Command Syntax: CURRent:PROTection:DELay <NRf+>
Parameter: Digits |MIN|MAX
Unit: s|ms
Example: CURRent:PROTection:DELay 0.5
Query Syntax: [SOURce:]CURRent:PROTection:DELay?
Parameter: None |MIN|MAX
Example: CURR:PROT:DEL? ; CURR:PROT:DEL?MIN ;
CURR:PROT:DEL? MAX
Returned Parameter: <NR3>
Related Commands: INP:PROT:CLE, CURR:PROT
[SOURce:]CURRent:PROTection:STATe
Disables/Enables current protection function.
Command Syntax: [SOURce:]CURRent:PROTection:STATe
<bool>
Parameter: ON|OFF
Example: CURR:PROT:STAT ON
Query Syntax: [SOURce:]CURRent:PROTection:STATe?
Parameter: None
Example: CURR:PROT:STAT?
Returned Parameter: <NR1> Value 0=OFF, 1=ON
Related Commands: CURR:PROT, INP:PROT:CLE
CURRent
[:LEVel]
[:IMMediate]
[:AMPLitude]
:LOW
:HIGH
:TRIGgered
[:AMPLitude]
:RISE
:RATE
[SOURce:]
TRANsient
[:STATe]
:MODE
:LTIMe
RESistance
[:LEVeI]
[:IMMediate]
[:AMPLitude]
:LOW
INPut
[:STATe]
:SHORt
[:STATe]
:LATCh
[:STATe]
:VOLTage
[:LEVel]
MEASure
[:SCALar]
:CURRent
[:DC]?
:VOLTage
[:DC]?
STATus
:QUEStionable
[:EVENt]?
:CONDition?
:ENABle
:ENABle?
:OPERation
SYSTem
:ERRor
[:NEXT]?
:VERSion?
:REMote
:LOCal
:REMote
:UPDate
:UPDate
:CODE
TRIGger
[:IMMediate]
:SOURce
:FUNCtion
ABORt
VOLTage
[:LEVeI]
[:IMMediate]
[:AMPLitude]
:LOW
POWer
[:LEVeI]
[:IMMediate]
[:AMPLitude]
MODE
LIST
[:STATe]
:MEMO
:NUMBer
:COUNt
:CHAin
:SAVE
:CLEar
BATTery
[:STATe]
:TERMinate
:VOLTage
:CAPacity
:CLEar
(
:ROOT
)