Gorilla 1500CTC Скачать руководство пользователя страница 74

Страница: 74 / 121

STEP 6B: ANGLE SUPPORTS

1: TWO 2 X 4 X 18" ANGLE SUPPORTS ARE MOUNTED UNDER THE DECK ON THE LEFT SIDE

OF THE PLAY SET TO THE 2 X 6 BOTTOM PANEL BOARD. THE TOP OF THE ANGLE SUPPORT

SHOULD BE FLUSH OR LOWER THAN THE TOP OF THE DECK SUPPORT.

2: AT THE TOP USE 2-1/2" WOOD SCREWS THROUGH THE ANGLE SUPPORT INTO THE

BOTTOM PANEL BOARD. AT THE BOTTOM USE ONE 2" AND ONE 3" WOOD SCREW TO

FASTEN THE ANGLE SUPPORT TO THE CORNER POST.

3: FOUR 2 X 4 X 13" ANGLE SUPPORTS ARE MOUNTED UNDER THE DECK ON THE FRONT

AND REAR OF THE PLAY SET TO THE 2 X 4 DECK SUPPORTS. THE TOP OF THE ANGLE

SUPPORT SHOULD BE FLUSH OR LOWER THAN THE TOP OF THE DECK SUPPORT.

4: AT THE TOP USE 2-1/2" WOOD SCREWS THROUGH THE DECK SUPPORT INTO THE ANGLE

SUPPORT. AT THE BOTTOM USE ONE 2" AND ONE 3" WOOD SCREW TO FASTEN THE ANGLE

SUPPORT TO THE CORNER POST.

TOP OF ANGLE SUPPORTS

SHOULD BE FLUSH OR LOWER

THAN THE DECK SUPPORT.

SCALE 1 : 8

DETAIL B

ANGLE

SUPPORT

BOARD

PANEL

BOTTOM

SUPPORT

ANGLE

2 X 4 X 18"

2 X 6

2 X 4 X 13"

DECK

SUPPORT

2 X 6

BOTTOM

PANEL

BOARD

2 X 4 X 18"

ANGLE

SUPPORT

2-1/2"

WOOD

SCREW

2 X 4 X 13"

ANGLE

SUPPORT

3" WOOD

SCREW

2" WOOD

SCREW

2" WOOD

SCREW

3" WOOD

SCREW

Содержание 1500CTC


























































































































Результаты поиска

Содержание 1500CTC

Отзывы:

Похожие инструкции для 1500CTC

Бренды по названию

Популярные бренды

Gorilla 1500CTC, Руководство пользователя

Результаты поиска

Содержание 1500CTC

Отзывы:

Похожие инструкции для 1500CTC

Бренды по названию

Популярные бренды