background image

IMPORTANT – PLEASE READ 

Congratulations! You have just purchase one of the finest residential wooden swing sets available today. As 
with any wooden product that spends its entire life outside, in varying elements, it is important to know what to 
expect with your new swing set so that your family can enjoy it for many years. 

As your swing set acclimates to its new environment, natural characteristics of the wood can show in the form 
of checks, or “cracks” in the lumber. In almost all cases this is normal and it will not affect the 

structural 

integrity of your play set and is not covered under warranty. 

 
KEEPING YOUR PLAYSET LIKE NEW 

MUST DO’s

 

The following owner responsibilities are crucial to the safety, integrity and aesthetic appeal of your 
swing set and may affect the warranty if not adhered to. 

WITHIN 60 DAYS 

• 

Check and tighten Hex Bolts/T-nuts, Carriage Bolts/Lock-nuts, and Lag Screws within the first 60 days and 

then twice annually – once before each season and then once during the season. 

WITHIN 90 DAYS 

• 

Apply a 

sealant

 or 

semi-transparent stain with sealant

 within the first 90 days of owning the swing set. Our 

own Stain/sealant is available online here:  http://www.gorillaplaysets.com/Playground-Sealant-p/10-0003.htm 

 Oil based stain or water based stain may be used. Should you choose to use other stain we suggest asking 

the product covering specialists at any number of specialty paint stores or home improvement centers for a 

product that would work best for your local environment. ** TIP – while the set is new, take a small board from 

to the store with you so they can color match the tint of the stain or sealant. 

 

SEASONAL REMINDERS 

 If your area experiences regular snowfall, remove your fabric tarp/canopy to avoid stretching, sagging or 

tearing of the material. Store it inside, folded up, and it will be as good as new when winter is over. 

 If your area experiences extremely cold temperatures, remove swing belts and other pliable features to 

prolong the lifespan of these play activities.

 

OTHER TIPS  

• 

Spray swing hangers with Pam, Mazola or olive oil to stop squeaking; do not use petroleum based products 

such as WD-40 or motor oil. 

• 

To repel yellow jackets and wasps, use a cotton ball and dab interior wooden corners underneath the play set 

deck with a liquid dish soap. Avoid using insecticides. 

 To speed up the slide wipe the center of slide with wax paper every 2 - 3 weeks. 

 
For additional safety and maintenance guidelines, please visit our website.

 

Содержание 1500CTC


























































































































Отзывы: