Gorilla 1500CTC Скачать руководство пользователя страница 78

Страница: 78 / 121

STEP 9: END WALL SLIDE MOUNT POST

1: FIND THE 4 X 4 X 40" END WALL SLIDE MOUNT POST.

2: MEASURE 26" INCHES FROM THE FRONT OF THE FRONT RIGHT CORNER POST AND MARK THE MEASUREMENT ON

THE INSIDE OF THE 2 X 6 X 79-1/2" ROPE LADDER SUPPORT. MEASURE DOWN 2" FROM THE TOP OF THE ROPE

LADDER SUPPORT AND MARK THE MEASUREMENT ON THE INSIDE. ALIGN THE TOP AND SIDE OF THE END WALL

SLIDE MOUNT POST WITH THE MARKS.

3: USE THREE 2-1/2" WOOD SCREWS TO ATTACH THE END WALL SLIDE MOUNT POST TO THE ROPE LADDER SUPPORT

FROM THE OUTSIDE OF THE ROPE LADDER SUPPORT.

4: THE END WALL SLIDE MOUNT POST CAN HANG FREELY AT THIS TIME.

SLIDE MOUNT

POST

FORT

FRONT OF

4 X 4 X 40"

END WALL

ROPE LADDER

SUPPORT

26"

POST

FRONT OF

END WALL

SLIDE MOUNT

(THREE)

FORT

WOOD SCREWS

4 X 4 X 40"

#8 X 2-1/2"

ROPE LADDER

SUPPORT

Содержание 1500CTC


























































































































Результаты поиска

Содержание 1500CTC

Отзывы:

Похожие инструкции для 1500CTC

Бренды по названию

Популярные бренды

Gorilla 1500CTC, Руководство пользователя

Результаты поиска

Содержание 1500CTC

Отзывы:

Похожие инструкции для 1500CTC

Бренды по названию

Популярные бренды