Gorilla Playsets Wilderness Gym II 1500JWF Скачать руководство пользователя страница 174

Страница: 174 / 174

8102

Telescope

Telescopio

Téléscope

NE 4610

, WS 4610

07-0040-G/Y, 07-0040-B/Y

WARNING: Assembly by adult.

AVERTISSEMENT: L’assemblage dolt être exécuté par un adulte.

ADVERTENCIA: El ensamblaje lo debe hacer un adulto.

WARNING: Assembly by adult.

AVERTISSEMENT: L’assemblage dolt être exécuté par un adulte.

ADVERTENCIA: El ensamblaje lo debe hacer un adulto.

Tools required | Outils requis | Herramientas requeridas

TELESCOPE:

1. Position Mounting Bracket in desired location.

2. Attach Mounting Bracket to the unit using the Mounting Screw provided.

3. Insert the Telescope into the Mounting Bracket as shown.

TÉLÉSCOPE:

1. Placez le support de fixation à l’endroit désiré.

2. Attachez le support de fixation à l’unité à l’aide des quatre vis de fixation fournies.

3. Insérez le télescope dans le support de fixation tel qu’illustré.

TELESCOPIO:

1. Ubique la abrazadera de montaje en la posición deseada.

2. Fije la abrazadera de montaje a la unidad usando el tornillo de montaje suministrado.

3. Inserte el telescopio en la abrazadera de montaje como se muestra.

Telescope Assembly

Ensamblaje del telescopio

Ensemble de télescope

Mounting Screw

Tornillo de montaje

Vis de fixation

Mounting Bracket

Abrazadera de montaje

Support de fixation

Specifications subject to change without notice. Les spécifications expsent pout changer sans la notification. Las especificaciones sujetas cambiar sin nota.

Manufactured for / fabriqué pour / fabricado para:

Backyard Play Systems

•

166 Etowah Industrial Ct.,

Canton, Georgia

• USA • 1-800-

882

0272

•

[email protected]

Made in China / Fait en China / Hecho en China • Printed in China / Imprimé en China / Impreso en China

11-25-19

Содержание Wilderness Gym II 1500JWF















































































































































































Результаты поиска

Содержание Wilderness Gym II 1500JWF

Отзывы:

Похожие инструкции для Wilderness Gym II 1500JWF

Бренды по названию

Популярные бренды

Gorilla Playsets Wilderness Gym II 1500JWF, Руководство пользователя

Результаты поиска

Содержание Wilderness Gym II 1500JWF

Отзывы:

Похожие инструкции для Wilderness Gym II 1500JWF

Бренды по названию

Популярные бренды