manualshive.com logo in svg

Gorilla Playsets Chateau Tower Treehouse with Fort Add On 1500AWFNS, Руководство по сборке, Страница: 59 / 146

Поделиться
Скачать
Gorilla Playsets Chateau Tower Treehouse with Fort Add On 1500AWFNS Скачать руководство пользователя страница 59

1-1/4" PAN HEAD SCREW

CLIMBING ROCKS

WASHER

LONG AS THEY WILL ALLOW PROPER ACCESS TO THE FORT.  BE CREATIVE!

CONFIGURATION MAY BE DIFFERENT THAT WHAT YOU SEE BELOW.  ROCKS CAN BE ARRANGED IN ANY PATTERN AS 

STEP 14:  ROCK WALL

1:  FIND TEN ROCKS AND THIRTY 1-1/4" PAN HEAD SCREWS WITH WASHERS.

2:  MOUNT THE ROCKS IN A STAGGERED MANNER ON THE ROCK WALL BOARDS.  THREE PAN HEAD SCREWS AND 

WASHERS WILL SECURE EACH ROCK TO THE WALL.

NOTE:  THE IMAGE SHOWN BELOW IS A GENERIC ARRANGEMENT OF ROCKS ON THE ROCK WALL.  YOUR ACTUAL 

3:  PLACE THE 5/4 X 3 X 23-7/8" ROCK WALL TOP CAP ON TOP OF THE ROCK WALL SIDES.  FASTEN THE ROCK WALL 

TOP CAP TO THE ROCK WALL SIDES WITH 2" WOOD SCREWS.

ROCK WALL TOP CAP

5/4 X 3 X 23-7/8"

2" WOOD SCREW

48

Содержание Chateau Tower Treehouse with Fort Add On 1500AWFNS



















































































































































Отзывы:

Нет отзывов