manualshive.com logo in svg

Gorilla Playsets Chateau Tower Treehouse with Fort Add On 1500AWFNS, Руководство по сборке, Страница: 54 / 146

Поделиться
Скачать
Gorilla Playsets Chateau Tower Treehouse with Fort Add On 1500AWFNS Скачать руководство пользователя страница 54

USE 2-1/2" WOOD SCREWS IN THESE LOCATIONS
ON EACH SIDE.

STEP 9: CENTER DECK SUPPORT

1:  FIND THE 2 X 4 X 70" CENTER DECK SUPPORT WITHOUT HOLES.

2:  FROM THE UNDERSIDE OF THE DECK SPACERS THAT WERE PREVIOUSLY INSTALLED, PLACE THE CENTER DECK

SUPPORT AT THE CENTER OF THE DECK SPACERS (USE THE HOLE ON CENTER AS A GUIDE) AND MAKE A MARK ON

THE OUTSIDE OF THE FORT TO REPRESENT A CENTER LINE.

3:  CENTER THE 2 X 4 X 70" CENTER DECK SUPPORT ON THESE MARKS AND PUSH THE CENTER DECK SUPPORT FLUSH

TO THE BOTTOM SIDE OF THE DECK BOARDS.

4:  USE 2" WOOD SCREWS TO ATTACH THE DECK SPACERS TO THE CENTER DECK SUPPORT.

5:  USING TWO 2-1/2" WOOD SCREWS, INSTALL THE 2 X 4 X 70" CENTER DECK SUPPORT THROUGH THE OUTSIDE OF

THE 2 X 6, AND INTO THE END OF THE CENTER DECK SUPPORT. REPEAT THIS STEP ON THE OPPOSITE END OF THE

FORT.

2" WOOD SCREW

2 X 4 X 70"

CENTER DECK SUPPORT

43

Содержание Chateau Tower Treehouse with Fort Add On 1500AWFNS



















































































































































Отзывы:

Нет отзывов