manualshive.com logo in svg

Gorilla Playsets Chateau Tower Treehouse with Fort Add On 1500AWFNS, Руководство по сборке, Страница: 145 / 146

Поделиться
Скачать
Gorilla Playsets Chateau Tower Treehouse with Fort Add On 1500AWFNS Скачать руководство пользователя страница 145

STEP 10: PANEL SLATS

1: INSTALL THE PANEL SLATS AT EQUAL LENGTHS. 
SEE DETAIL BELOW FOR MEASUREMENTS.

2: ATTACH THE PANEL SLATS TO THE FORT WITH 
2" WOOD SCREWS IN THE PRE-DRILLED HOLES.

THE PLAYSET.

VIEW FROM INSIDE

PANEL SLAT

5/4 X 6 X 28-1/4"

PANEL SLAT

5/4 X 2-5/8 X 28-1/4"

SWING BEAM SIDE

 12 14 " 

VIEW FROM OUTSIDE

LADDER SIDE

THE PLAYSET.

5/4 X 2-5/8 X 28-1/4" PANEL SLAT

5/4 X 6 X 28-1/4"
PANEL SLAT

 19 38 " 

2 X 4 X 28-9/16"

5/4 X 6 X 28-1/4" PANEL SLAT

CENTER POST

VIEW FROM INSIDE

 THE PLAYSET.

5/4 X 2-5/8 X 28-1/4" PANEL SLAT

THIS PANEL 

WERE REMOVED FOR

A TIRE SWING

BEAM

CLARITY.

TIRESWING 

NOTE: SOME BOARDS

FRONT OF PLAYSET

IF YOU HAVE 

THEN LEAVE

SLAT OFF.

AND MOVE 

THIS SLAT

AGAINST THE 

TIRE SWING 

BEAM.

26

Содержание Chateau Tower Treehouse with Fort Add On 1500AWFNS



















































































































































Отзывы:

Нет отзывов