Gorilla Playsets Blue Ridge Mountaineer 2009 Скачать руководство пользователя страница 38

Страница: 38 / 92

8 "

4 1

4 4

1 "

2 34 "

USE 2-1/2" WOOD SCREWS

IN THESE LOCATIONS

USE 2-1/2" WOOD SCREWS

IN THESE LOCATIONS

DECK SPACER

5/4 X 4 X 22-1/2"

DECK SPACER

5/4 X 4 X 14-1/2"

DECK SPACER

BOARDS TO THE CENTER DECK SUPPORTS WITH 2"

WOOD SCREWS.

ATTACH TO THE 4 X 4 SLIDE MOUNT ON THE SLIDE END

OF THE FORT. FASTEN DECK SPACERS AND DECK

2: START WITH A 5/4 X 6 X 47-1/2"

NOTE: THE TOP OF THE SCREW

BETWEEN THE DECK BOARDS.

TOP OF THE DECK BOARDS.

HEAD SHOULD BE FLUSH TO THE

DECK BOARD

2" WOOD SCREW

5/4 X 6 X 47-1/2"

UNIFORM (APPROX. 1/4") SPACE

DECK SUPPORT BELOW. LEAVE A

PREDRILED HOLES AND INTO THE

WOOD SCREWS THROUGH THE

BOARD AND ATTACH IT WITH 2"

AND THE REAR BOTTOM PANEL

BETWEEN THE FRONT FACE BOARD

FORT. CENTER THE BOARD

DECK BOARD AT ONE END OF THE

3: FROM THE UNDERSIDE OF THE DECK BOARDS THAT

WERE PREVIOUSLY INSTALLED, PLACE THE CENTER

DECK SUPPORTS ON THE SIDES OF THE END WALL

SLIDE MOUNT, AND FASTEN WITH THREE 2-1/2" WOOD

SCREWS;(USE THE PRE-DRILLED HOLES IN THE DECK

BOARDS AS A GUIDE) AND MAKE A MARK ON THE

OUTSIDE OF THE FORT TO REPRESENT A CENTER LINE

FOR EACH CENTER DECK SUPPORT.

5: CENTER THE 2 X 4 X 70" CENTER DECK SUPPORTS

ON THESE MARKS AND PUSH THE CENTER DECK

SUPPORTS FLUSH TO THE BOTTOM SIDE OF THE DECK

BOARDS.

6: USING TWO 2-1/2" WOOD SCREWS, INSTALL THE 2 X

4 X 70" CENTER DECK SUPPORT THROUGH THE

OUTSIDE OF THE 2 X 6, INTO THE END OF THE CENTER

DECK SUPPORT ON THE SWING BEAM SIDE, AND

5/4 X 4 X 22-1/2"

DECK SPACER

5/4 X 4 X 14-1/2"

8 "

3 "

4 "

STEP 10: DECK BOARDS

THE FOLLOWING STEP IS RECOMMENDED TO PREVENT POSSIBLE SPLITS IN THE WOOD

1: PRE-DRILL THE ENDS OF THE DECK BOARDS TO PREVENT INSTALLATION DAMAGE. PRE-DRILL BOTH ENDS WITH A

1/8" DRILL BIT AT THE DIMENSIONS SHOWN BELOW. THE HOLE AT 22-1/8" ONLY NEEDS TO BE DRILLED ONCE.

Содержание Blue Ridge Mountaineer 2009





























































































Результаты поиска

Содержание Blue Ridge Mountaineer 2009

Отзывы:

Похожие инструкции для Blue Ridge Mountaineer 2009

Бренды по названию

Популярные бренды

Gorilla Playsets Blue Ridge Mountaineer 2009, Инструкция по сборке

Результаты поиска

Содержание Blue Ridge Mountaineer 2009

Отзывы:

Похожие инструкции для Blue Ridge Mountaineer 2009

Бренды по названию

Популярные бренды