Gorilla Playsets Blue Ridge Mountaineer 2009 Скачать руководство пользователя страница 34

Страница: 34 / 92

5/16" WASHER

2 X 4 X 70"

2 X 6 X 70"

REAR TOP PANEL BOARD

SANDBOX BOARD

CORNER POSTS FOR

THE LAG SCREWS.

LAG SCREWS ARE

SELF-TAPPING.

7: PLACE THE FRAME

IN ITS FINAL POSITION

AND FOLLOW THE

PROCEDURES AT THE

FRONT OF THE

MANUAL TO LEVEL

AND SQUARE THE

STRUCTURE. ONCE

THE FRAME IS LEVEL,

SQUARE, AND SET

INTO POSITION; GO

BACK AND INSERT THE

5/16 X 3-1/2" LAG

SCREWS AND 5/16"

WASHERS IN ALL OF

THE REMAINING

HOLES OF THE 2 X 6

PARTS. NOTE: THERE

WILL NOT BE ANY

PREDRILLED

HOLES IN THE

5/16 X 4-1/2"

HEX BOLT

2 X 6 X 70"

REAR ENTRY BOARD

STEP 6: REAR FRAME ASSEMBLY

1: PLACE THE 2 X 6 X 70" SANDBOX BOARD ON THE REAR OF THE CORNER POSTS. THE OFFSET HOLES IN THE

SANDBOX BOARD MUST FACE UP.

2: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE TOP HOLES OF THE SANDBOX BOARD TO THE

T-NUTS INSTALLED ON THE CORNER POSTS. THE BOTTOM HOLES WILL BE USED LATER.

3: PLACE THE 2 X 6 X 70" REAR ENTRY BOARD ON THE FRONT OF THE CORNER POSTS. THE OFFSET HOLES IN

THE FRONT FACE BOARD MUST FACE UP.

4: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE TOP HOLES OF THE REAR FACE BOARD TO THE T-

NUTS INSTALLED ON THE CORNER POSTS. THE BOTTOM HOLES WILL BE USED LATER.

5: PLACE THE 2 X 4 X 70" REAR TOP PANEL BOARD ON THE FRONT OF THE CORNER POSTS. THE OFFSET HOLES IN THE

TOP PANEL BOARD MUST FACE UP.

6: USE 5/16 X 4-1/2" HEX BOLTS AND 5/16" WASHERS TO ATTACH THE TOP HOLES OF THE TOP PANEL BOARD TO

THE T-NUTS INSTALLED ON THE CORNER POSTS.

Содержание Blue Ridge Mountaineer 2009





























































































Результаты поиска

Содержание Blue Ridge Mountaineer 2009

Отзывы:

Похожие инструкции для Blue Ridge Mountaineer 2009

Бренды по названию

Популярные бренды

Gorilla Playsets Blue Ridge Mountaineer 2009, Инструкция по сборке

Результаты поиска

Содержание Blue Ridge Mountaineer 2009

Отзывы:

Похожие инструкции для Blue Ridge Mountaineer 2009

Бренды по названию

Популярные бренды