background image

13.8.2014202066 
 

                                                                                                            

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

  To  ignite  the  burner,  press  the  selected  burner  button  and 

turn  it  to  the maximum  power  position  (large  flame symbol). 
Electric spark from the ignition device ignites the gas. 

   If  the  ignition  device  is  out  of  order  (power  failure  or 

humidity), use a match or a lighter to ignite the gas. Keep the 
button pressed for approximately 10 seconds after ignition to 
stabilize the flame. 

  After  that  you  can  set  the  burning  power  between  high  and 

low  position  to  suit  your  cooking  requirements.  Button 

positions between  

  and 

are not recommended. In 

these  positions  the  flame  is  not  stabilized  and  may  be 
extinguished. 

 
 
 
 
 
 
 
 
 
 
 
 
     
 
 
 
 
 

•   To shut the burner off turn the button to the right, to the OFF 

position 

 
 
 
 
 
 
 
 
 

 

 

Always push the button in before starting to turn it! 

 
 

  

Če se po 15 sekundah gorilnik ni prižgal, zaprite

 

gorilnik in 

počakajte  najmanj  1  minuto.  Potem  ponovite  postopek 

prižiganja.

 

 

Če plamen gorilnika ugasne-vseeno zaradi katerega vzroka-
zaprite  gorilnik  in  pred  preizkusom  ponovnega  vžiga 
počakajte vsaj 1 minuto.

 

 

 
 

Burner type

 

Dish diameter

 

Large

 (3kW)

 

220 - 260mm 

Auxiliary

 (1 kW)

 

120 - 180mm 

Double (WOK) - interior

 

flame  

(1kW) 

120 - 180mm 

Double (WOK) - all

 

flame  

 

220 - 300mm 

 

  

If you failed to ignite the burner after 15 seconds,

 

shut  the  burner  off  and  wait  for  at  least  one  minute 
before the next attempt.

 

 

If  the  burner  flame  goes  out  (for  whatever  reason), 

shut  the  burner  off  and  wait  for  at  least  one  minute 
before next attempt.

 

 
 

 

 

 

Содержание GC341UC

























Отзывы: