background image

 

Installing the foam 
gasket
 

 

 

 

Before inserting the appliance into the opening in the kitchen worktop, the supplied foam 
gasket must be attached to the lower side of the glass. 
Do not install the appliance without the foam gasket! 

 

The gasket should be attached to the appliance in the following way: 

 

Remove the protective film from the gasket. 

 

Attach the gasket to the lower side approximately A=2-3 mm from the edge. The gasket 
must be attached along the entire length and should not overlap at the corners. 

 

When installing the gasket, make sure that the glass does not come into contact with any 
sharp objects. 

Installation procedure 

 

 

Worktop must be absolutely horizontal; 

 

Seal the cut surfaces with a suitable sealant to avoid swelling caused by moisture. The 
sealant must be heat resistant; 

 

Put the supplied springs in their places; 

 

Feed the mains connection cable down through the cut-out; 

 

Insert the appliance into the cut-out; 

 

Press the appliance firmly towards the worktop from above. 

 

 

 

 

CONNECTION TO THE POWER SUPPLY 

 

 

 

The appliance may ONLY be connected by an authorized qualified technician. 

 

Electric system protection should comply with all relevant regulations. 

 

The connection clips can be accessed when the connection clip covers are opened / 
removed. 

 

Before connecting the appliance, make sure the voltage indicated on the rating plate is 
consistent with the voltage in your home network. Connection voltage should be checked 
by a qualified technician using a corresponding measuring device! 

 

The rating plate with basic information is attached on the lower side of the appliance. 

 

In order to make a fixed connection to the mains, insert an all-pole circuit breaker 
between the appliance and the mains. This device shall have a contact separation in all 
poles, providing full disconnection under overvoltage category III conditions. 

 

The current conducting and isolated parts must be protected from any possibility of direct 
contact. 

 

 

WARNING! 

 

Before any intervention, disconnect the appliance from the power mains. Connect the 
appliance in compliance with the electric connections diagram supplied; make sure the 
relevant network voltage is observed!  

 

The ground wire should be connected to the clip indicated by the earth symbol. 

 

The mains cable should be fed through the fastening clip which protects it from being 
accidentally pulled out. 

 

After connecting the appliance, turn on all cooking zones / heaters for approximately 
three minutes to make sure they are operating correctly. 

 

Incorrect connection may destroy parts of the appliance, making the warranty void. 

 

Connection cable on the back of the appliance should be led in such way that it does not 
touch the appliance back wall, as this part will get very hot during operation. 

 

Basic adjustment of 
sensors to the ambience
 
 

Upon each connection to the power supply the sensors of the appliance are automatically 
adjusted to the environment to ensure their proper function.  
All displays turn on and are fully illuminated for a few seconds. 
During the adjustment procedure the sensors must be free of any objects, otherwise the 
adjustment procedure will be interrupted until such objects are removed from the sensor 
surface. During this period the regulation of the cooktop is impossible. 

 

User interface initial 
calibration 
 

The hob control panel has implemented an initial keyboard calibration focused to adapt 
the sensibility of the keys, to the final mechanical, environmental and user conditions. 
Any time the hob is plugged in or there is a power failure that results in a reset of the user 
interface, keyboard sensitivity will be readjusted at the first touch of the sensor. This first 
touch must be done in certain conditions: 

 Do not use gloves 

 Use a clean finger 

Содержание 731579/01














Отзывы: