Goodwe GW11K4-MS-US30 Скачать руководство пользователя страница 8

Страница: 8 / 51

User Manual V1.0-2022-08-20

02 Safety Precaution

DANGER High voltage hazard.

Disconnect all incoming power

and turn off the product before

working on it.

Delayed discharge. Wait

5 minutes after power off

until the components are

completely discharged.

Read through the user manual

before working on this device.

Potential risks exist. Wear

proper PPE before any

operations.

High-temperature hazard. Do

not touch the product under

operation to avoid being burnt.

Grounding point.

SGS Marking for the United

States of America and Canada.

Do not dispose of the inverter

as household waste. Discard

the product in compliance with

local laws and regulations,

or send it back to the

manufacturer.

Support Type 1 DC Arc

detection on PV side.

AFCI

Type 1

WARNING

• The voltage and frequency at the connection point meet the inverter grid connection

requirements

•

Additional protective devices like circuit breakers or fuses are recommended on the AC

side. Specification of the protective device should be at least 1.25 times the rated AC output

rated current.

• Make sure that all the groundings are tightly connected. When there are multiple

• inverters,make sure that all the grounding points on the enclosures are equipotential

•

bonding.You are recommended to use copper cables as AC output cables. Contact the

manufacturer if you want to use other cables.

2.3 AC Side

2.4 Inverter Installation

DANGER

• Do not apply mechanical load to the terminals, otherwise the terminals can be damaged.
•

All labels and warning marks should be visible after the installation. Do not scrawl,

damage, or cover any label on the device.

• Inverters should not be installed in multiple phase combination.
• Warning labels on the inverter are as follows.

Содержание GW11K4-MS-US30




















































Результаты поиска

Содержание GW11K4-MS-US30

Отзывы:

Похожие инструкции для GW11K4-MS-US30

Бренды по названию

Популярные бренды

Goodwe GW11K4-MS-US30, Руководство пользователя

Результаты поиска

Содержание GW11K4-MS-US30

Отзывы:

Похожие инструкции для GW11K4-MS-US30

Бренды по названию

Популярные бренды