manualshive.com logo in svg

Goodman ACVC8 CA Series AMVC8 CA Series, Обслуживание и устранение неисправностей, Страница: 50 / 53

Поделиться
Скачать
Goodman ACVC8 CA Series AMVC8 CA Series Скачать руководство пользователя страница 50

•  Furnace fails to operate.
•  Integrated control module LED 
display provides 

 error code.

•  Integrated control 
module has lost 
communications w ith 

circulator blow er 
motor.

•  Loose w iring connection 
at circulator motor control 
leads.

•  Failed circulator blow er 
motor.

•  Failed integrated control 
module.

•  Furnace fails to operate.

•  Integrated control module LED 
display provides 

 error code.

•  Circulator blow er 

motor horse pow er in 
shared data set does 

not match circulator 
blow er motor horse 
pow er.

•  Incorrect circulator blow er 

motor in furnace.
•  Incorrect shared data set 

in integrated control module.

•  Furnace operates at reduced 

performance.
•  Airfow  delivered is less than 

expected.
•  Integrated control module LED 
display provides 

 error code.

•  Circulator blow er 

motor is operating in a 
pow er, temperature, 

or speed limiting 
condition.

•  Blocked filters.

•  Restrictive ductw ork.
•  Undersized ductw ork.

•  High ambient 
temperatures.

•  Verify circulator blow er if motor 

horse pow er is the same specifed 
for the specifc furnace model. 

Replace if necessary.
•  Verify shared data set is correct 
for the specifc model. Re-populate 

data using correct memory card if 
required.

•  Turn pow er OFF prior to 

repair
•  Replace motor w ith correct 

replacement part.
•  Use memory card for the 
specifc model

•  Insert memory card 
BEFORE turning pow er ON. 

Memory card may be 
removed after data is loaded 
and pow er is turned off.

•  Error code w ill be cleared 
once shared data and motor 

horse pow er match.

•  Check filters for blockage.  Clean 

filters or remove obstruction.
•  Check ductw ork for blockage. 

Remove obstruction. Verify all 
registers are fully open.
•  Verify ductw ork is appropriately 

sized for system. Resize/replace 
ductw ork if necessary.

•  See "III. Product Description" and 
"IV. Location Requirements & 
Considerations" furnace installation 

requirements.

•  Turn pow er OFF prior to 

repair.

•  Tighten or correct w iring 
connection.
•  Check circulator blow er motor. 

Replace if necessary.
•  Check integrated control module. 

Replace if necessary.

•  Turn pow er OFF prior to 
repair
•  Replace circulator motor 

w ith correct replacement 
part.

•  Replace integrated control 
module w ith correct 
replacement part.

Symptoms of Abnormal 

Operation 

Diagnostic / 

Status LED 

Codes

Possible Causes

Corrective Actions

Notes & Cautions

Fault Description

TROUBLESHOOTING

50

Содержание ACVC8 CA Series AMVC8 CA Series






















































Отзывы:

Нет отзывов