background image

Single Stage

Single Stage

Single Stage

Single Stage

Single Stage

Temperature Control

Temperature Control

Temperature Control

Temperature Control

Temperature Control

Description

Description

Description

Description

Description

The SP-33 and SP-33D controls are single stage,
general purpose, temperature controls for use in
HVAC, refrigeration, and industrial applications.
The setpoint temperature range is user selectable
from:

40°F to +104°F

The SP-33 control provides one isolated SPDT
relay output while the SP-33D provides two (ef-
fectively DPDT).  The relays on both the SP-33
and SP-33D are controlled by comparing the
thermistor temperature sensor to the  adjustable
setpoint temperature.  The user can select either
“heat” mode (relay operates on temperature fall)
or “cool” mode (relay operates on temperature
rise).  The control setpoint can be set using the

internal setpoint dial (factory setting) or  a remote
setpoint dial (see Goldline RSP-33 remote set-
point on page 7).  The SP-33 and SP-33D also
features a plug in connector for a TD-30 Digital
Display Monitor.  The TD-30 snaps into the cover
for easy mounting and displays both sensor and
setpoint temperatures.

Power can be provided from a 24VAC, 24VDC,
115VAC or 240VAC power source.  Relay con-
tacts are completely isolated so the outputs can
switch any voltage, regardless of the power source.
On SP-33D models, one relay output can switch
high voltage, the other switch low voltage.  A
movable divider is provided to separate high and
low voltage wiring compartments.

Sensors: Thermistor, 10K @ 25°C/77°F

Type SW supplied with control
Interchangeable with any IE
temperature sensor
1000 ft. maximum wire run

Setpoint:

40 to +104°F

Differential:

1-25°F

Accuracy:

+/- 1°F

Environment:

-30 to +130°F
0-95% rH, non-condensing

Specifications

Specifications

Specifications

Specifications

Specifications

Power:

Approx. 2VA required from any power
source:
21-27VDC
21-27VAC, 50/60Hz
105-130VAC, 50/60Hz
195-250VAC, 50/60Hz

Outputs: SPDT isolated (dry)contacts,

1HP@115VAC,  2HP@240VAC
rating @ 240VAC:

20A on NO contacts
10A on NC contacts

SP-33

SP-33

SP-33

SP-33

SP-33

SP-33D

SP-33D

SP-33D

SP-33D

SP-33D

Содержание SP-33








Отзывы: