Technical Data
Antenna
(
Fold 90°, rotate 360 °
)
1/
4λ
Audio Input Port
3.5mm Port
USB Type-C 5V 0.2A
Power Supply
Battery
Two AA batteries
5V 0.2A
Two AA batteries
Working Temperature Range
Signal Noise Ratio
0℃-50℃
≈70dB
0℃-50℃
≈70dB
Receive Sensitivity
\
-47dBV
Distortion
Material
Metal
Metal
\
Below 0.5%
Size
63*21*198 mm
63*24*198 mm
Net Weight
212 g
226 g
Name
Body-pack Transmitter TX1
Portable Receiver RX1
Model
WMicS1 Pro TX
WMicS1 Pro RX
Selectable Channel
96(Group A: 48; Group B: 48)
RF Frequency Range
514MHz - 596MHz
Channel Group
A/B
Oscillator Type
Crystal Controlled PLL
Synthesizer
Audio Frequency Range
50Hz-20KHz
Sound Delay
12ms
1/
4λ
3.5mm Port
96(Group A: 48; Group B: 48)
514MHz - 596MHz
A/B
Crystal Controlled PLL
Synthesizer
50Hz-20KHz
12ms
Avoid sudden drops. The device may fail to work after strong shocks, impacts, or excess
stress.
Keep dry. The product isn’t water-proof. Malfunction, rust, and corrosion may occur and go
beyond repair if soaked in water or exposed to high humidity.
Avoid sudden temperature changes. Condensation happens if sudden temperature
changes such as the circumstance when taking the transmitter and receiver out of a
building with higher temperature to outside in winter. Please put the transmitter and
receiver in a handbag or plastic bag beforehand.
Keep away from strong magnetic field. The strong static or magnetic field produced by
devices such as radio transmitters leads to malfunction.
This product, except consumables e.g. lapel microphone, is supported with a one-year
warranty.
Unauthorized service will void the warranty.
If the product had failures or was wetted, do not use it until it is repaired by professionals.
Changes made to the specifications or designs may not be reflected in this manual.
GODOX Photo Equipment Co,Ltd. hereby declares that the This equipment are in
compliance with the essential requirements and other relevant provisions of EU Directive
2014/53/EU. They are allowed to be used in all EU member states.
For more information of DoC, Please click this web link:http://www.godox.com/DOC/Go-
dox_WMicS1Pro_DOC.pdf
Maintenance
Unable to receive audio signal. Make sure batteries are installed correctly and Power
Switch is turned on. Check if the transmitter and the receiver are set to the same
channel, if the microphone or earphone is well connected, or if the devices are set to the
correct mode.
Check if the transmitter is set to silent mode or not.
Signal disturbance or shooting interference. Change a different channel of the transmit-
ter and receiver.
Operating audio distance limited or signal missing. Check if batteries are exhausted. If
so, replace them.
Troubleshooting
Declaration of Conformity:
•
•
•
•
Insert the omnidirectional lavalier microphone into the transmitter’s MIC port.
Turn on the transmitter to set the relevant parameters.
Clip the transmitter onto the belt or put it into your pocket.
Transmitter
①
②
③
Connect the 1/4” cold shoe onto the receiver, and install them on the camera or
shooting equipment.
Insert one end of the 3.5mm cable into the receiver’s OUTPUT port and the other
end into camera’s MIC port.
Turn on the receiver to set relevant parameters.
Note: Please set the group and channels of transmitter and receiver to the same when setting parameters.
When a receiver is connecting to two transmitters, A transmitter must be set and used in A group while B
transmitter must be set and used in B group.
Receiver
①
②
③
