background image

-  31  -

-  32  -

AD400Pro can only be set as slave unit (receiver end). Press Wireless Selection Button to switch.

Wireless Flash Mode

Features

1.

 This flash unit uses Li-ion polymer battery which has long runtime. The available charge-and-discharge times are 

over 300.

2. 

It is reliably safe. The inner circuit is against overcharge, overdischarge, overcurrent, and short circuit.

3. 

Take only 2 hours to fully charge the battery by using the standard battery charger. 

Cautions

     Do not short circuit.
     Do not expose to rain or immerse into water. This battery is not water proof.
     Keep out of reach of children.
     No over 24 hours' continuous charging.
     Store in dry, cool, ventilated places.
     Do not put aside or into fire.
     Dead batteries should be disposed according to local regulations.
     Please charge the battery to approx. 60% before being placed for long time.
     If the battery had ceased using for over 3 months, please make a full recharge.

Loading and Unloading the Battery Pack

Push down the battery pack 

2

until it is locked.

Match the buckles of the battery 

1

and the main body. . 

Push the battery pack upward 

2

to unload it.

Push the Battery Locking Ring 

1

backwardly.

Loading:

Unloading: 

Power Management

Long press the Power Switch for 1 seconds to control the on/off of the flash unit. Turn off the power pack if the flash 
unit will not be used for an extended period. This product has auto power off function. The flash will auto power off 
in 30 to 120 min. which is set on C.Fn-STANDBY.

Battery Level Indication

 

Attach the battery pack to the flash correctly. Be aware of the battery level by check the battery level indication on 
the LCD panel when using.

Note: The indications are almost the same except of grids shift.

3 grids
2 grids
1 grid
Blank grid
Low battery and 
charging reminder

1 red grid +3 green grids
1 red grid +2 green grids
1 red grid +1 green grid
1 red grid
2%: red light blinks
1%: the indicator is off.

75%~100%
50%~75%
25%~50%
3%~25%

Battery Level Indication 

on the LCD Panel

(

Indicating battery level and 

management of the whole flash 
system

)

LED Battery Level Indication on 

the Battery

(Indicating battery level and 

management of non-loaded battery)

<2%

The battery level is going to be used out immediately. 

And the flash will alarm for the 1 minute and auto power 

off in 3 minutes. Note: Please recharge the battery as 

soon as possible (within 10 days). Then, the battery can 

be used or be placed for long period. 

Meaning/Percentage of Battery Level

Battery

0

180

Adjusting Handle

1.

 When the Direction Adjusting Handle 

    is not pulled out, screw clockwise 

    while unscrew anti clockwise.

2. 

The Direction Adjusting Handle's rotation angle should be restrained from 0 to 

    180 degrees below the flash body. Please pull out the Direction Adjusting 

    Handle, adjust the appropriate angle, and manipulate the step 1 before colliding 

    with the flash body.

Detaching the 

Mounting Bracket

Detaching the Handle

1.

 Insert a coin or corresponding 

wrench(not included) into the Bracket 

Fixing Screw and loosen it anti-

clockwise to detach. 

1.

 Insert the included wrench into the 

Handle Fixing Screw and loosen it anti-

clockwise to detach.

Содержание WITSTRO AD400Pro














Отзывы: