LED
MENU
TEST
LED
MENU
TEST
LED
MENU
TEST
GR/CH Button
Special Effects ON/OFF:
In LED mode, press the
modeling lamp/special effects button, and the special
effects will be on or off. Turn the modeling lamp/special
effects button to choose from the eight special modes.
Short press the GR/CH button can adjust the wireless
groups. When the group icon on the LCD panel is blinking,
turn the light brightness adjustment button to set the
groups. Long press the GR/CH button to adjust the
wireless channels. When the channel icon on the LCD
panel is blinking, turn the light brightness adjustment
button to set the channels.
Modeling Lamp/Special Effect Button
Modeling lamp ON/OFF:
In flash mode, press the
modeling lamp/special effects button to turn on or off the
modeling lamp. When modeling lamp is on, turn the
modeling lamp/special effects button to adjust the light
brightness of modeling lamp from 5% to 100%.
MENU Button
Press the Menu button to enter custom setting area.
Custom Function Setting
Custom Function
Signs
F1
F2
Functions
Wireless ID
Power output
display mode
Setting Signs
OF
01~ 99
1/P
P.P
Settings & Descriptions
Off ID
Choose any figure from 01~99
Display power in the form of fractions
Display power in the form of fraction decimal
Restrictions
No
Flash mode
Wireless Control in LED Mode
With 2.4G wireless system, FV series have remote grouping and control function. Up to 16 groups of LED lights
can be controlled. 32 channels and 100 wireless IDs are available with strong anti-interference capability.
Please set the channels and groups of LED light to the same as those of RC-A6 remote control before usage.
Adjusting Channel/Group with the Remote Control
● Press the CH/GR button and the group icon blinks. Press the“-”“+”button to choose a group (A to F, 0 to 9).
● Press the CH/GR button twice and the channel icon blinks. Press the“-”“+”button to choose a channel (1 to 32).
Adjusting ID with the Remote Control
● Double click the CH/GR button and press the“-”“+”button to choose ID from OFF or 0 to 99.
Adjusting Light Brightness with the Remote Control
● Press the“-””+“button to adjust the light brightness.
Adjusting Color Temperature with the Remote Control
● Press the SET button of the remote control and the color temperature icon blinks. Press the“-”“+”button to adjust
the color temperature.
Remote control reset:
press down "-" and "+" button simultaneously to reset.
XPro series:
Set the C.Fn-DIST to 0-30m.
→
Please turn on the “close distance wireless mode” on the flash trigger (
＜
0.5m):
4. Whether the flash trigger and the receiver end equipment are in the low battery states or not
1. Disturbed by the 2.4G signal in outer environment (e.g. wireless base station, 2.4G wifi router,
Bluetooth, etc.)
→
To adjust the channel CH setting on the flash trigger (add 10+ channels) and use the channel which is not
disturbed. Or turn off the other 2.4G equipment in working.
2. Please make sure that whether the flash has finished its recycle or caught up with the continuous
shooting speed or not(the flash ready indicator is lighten) and the flash is not under the state of over-
heat protection or other abnormal situation.
→
Please downgrade the flash power output. If the flash is in TTL mode, please try to change it to M mode(a
preflash is needed in TTL mode).
X1, X2 and XPro series:
press the test button and hold on, then turning it on until the flash ready indicator
blinks for 2 times.
3. Whether the distance between the flash trigger and the flash is too close or not
→
Please replace the battery(the flash trigger is recommended to use 1.5V disposable alkaline battery).
The Reason & Solution of Not Triggering in Godox 2.4G Wireless
Note: The wireless signal can be received only when the controller of LED light is powered on.
- 13 -
- 14 -
Flash Mode
In flash mode, FV series has 2.4G wireless receiving functions. Purchase Godox X
series flash trigger e.g. X1, X2, XPro series and XT 32 flash trigger to wirelessly
control FV series' power, modeling lamp's on/off and triggering.
2.4G Wireless control
Display
Scene
FX1
Flash1
FX2
Flash2
FX3
Flash3
FX4
Storm1
FX5
Storm2
FX6
Storm3
FX7
TV
Fx8
Broken bulb
LED Special Effects Mode
In LED mode, 8 FX special effects mode can be set to simulate various of shooting scene and achieve creative
shooting.
Sync Triggering
The sync cord jack is aΦ3.5mm plug. Insert a trigger plug
here and the flash will be fired synchronously with the
camera shutter.
Setting color temperature range
The factory setting of remote control's color temperature range is 2500-10000K.
In order to use remote control conveniently, color temperature range settings are added: when the remote
control is off, hold down the SET button and turn it on to enter color temperature adjusting interface. Press
CH/GR button to switch the lowest and highest color temperature value and press "-" or "+" button to change the
value. Press the SET button to confirm it.
