Godiva PowerFlow 12/10 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 424

background image

7

©Godiva Ltd. Our policy is one of continuous development. We therefore reserve the
right to amend specifications without notice or obligation.

DO NOT REFUEL unless the engine is stationary and COLD.

ENSURE that the fuel cap is secure and DO NOT overfill the tank.

Avoid prolonged skin contact with fluids, particularly if corrosive or carcinogenic.

When in use, keep ALL UNTRAINED people AWAY from the unit.

Where appropriate, eye protection should be worn.

DO NOT run the engine with the battery disconnected.

Disconnect the negative (-ve) battery lead first and reconnect last.

Isolate the electrical supply when working on the pump.

Avoid battery spillage.

Batteries produce EXPLOSIVE GASES, do not expose to sources of heat and
naked flames.

DO NOT lift heavy weights without assistance.

DO NOT remove protective guards or shields.

When cleaning the pump and engine use hot soapy water, do not use

flammable degreasers.

When cleaning the pump and engine use hot soapy water, do not use

flammable degreasers.

Noise

Operators must wear suitable EAR PROTECTION when the pump is running.

Gauges

Do not clean the glass surfaces of the gauges with abrasive or solvent cleaners. These
will cloud the glass surface. Use a mild detergent and water.

ENVIRONMENTAL PROTECTION

It  is  prohibited  to  pour  engine  oil  and  other  contaminants  onto  the  ground,  down
sewers, drains, or into water courses.
Dispose  of  lubricants  through  authorised  waste  disposal  contractors,  licensed  waste
disposal sites, or to the waste reclamation trade.
If  in  doubt,  contact  your  Local  Environmental  Agency  for  advice  regarding  disposal
policies.

End of life disposal

– please dispose of the pump according to local regulations relating

to recycling of materials.

«
...
6
7
8
9
10
...
»

Содержание PowerFlow 12/10









































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerFlow 12/10

Бренд: TANKLESS Страницы: 72

Бренд: SAER Elettropompe Страницы: 72

Бренд: York Страницы: 204

Бренд: GEA Страницы: 337

Бренд: Liberty Pumps Страницы: 16

Бренд: OEG Страницы: 28

Бренд: Homa Страницы: 24

HYDROMATIC SP50

Бренд: Pentair Pool Products Страницы: 12

Бренд: Zodiac Страницы: 32

Бренд: Barmesa Pumps Страницы: 15

Бренд: GORMAN-RUPP PUMPS Страницы: 25

Бренд: Intex Страницы: 5

Бренд: UDOR Страницы: 96

Бренд: GORMAN-RUPP PUMPS Страницы: 52

Бренд: Jandy Страницы: 72

E1+P GI 11,4 T SD

Бренд: DAB Страницы: 184

Solar Storage Tank Water Heater

Бренд: American Water Heater Страницы: 15

Бренд: AQUASYSTEM Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды