Godiva PowerFlow 12/10 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 424

background image

23

©Godiva Ltd. Our policy is one of continuous development. We therefore reserve the
right to amend specifications without notice or obligation.

Pump Tests

Running Test

Note: Valves, hoses and connectors may vary with customer specification.

To ensure the pump is kept in good condition and keep the battery charged, it is
recommended that the pump should be run once a month for 30 minutes.

1.  Connect the pump to suction at a depth of between 1 metre and 3 metres.
2.  Start and run the engine.
3.  Prime the pump.
4.  Open the delivery valve.
5.  Run the pump at a pressure of 3 bar for approximately 30 minutes.
6.  Stop the pump and drain volute.

Vacuum Test - Exhaust Gas Priming

Secure  the  suction  tube  blanking  cap,  close  the  delivery  valve  and  open  the  manual
priming valve.
Start the engine, fully open the throttle and pull up the priming lever.
With a vacuum reading of 0.6 bar (18“hg) registering on the compound gauge, release
the priming lever and stop the engine. The vacuum reading must be maintained for a
minimum of 15 seconds. If vacuum retention fails, proceed to a pressure test to identify
the cause.
Should the pump be incapable of developing a vacuum of  0.6 bar,  but  hold  whatever
vacuum it does develop, a fault in the priming system or gauge is indicated.
NOTE:  Do  not  run  the  pump  for  more  than  30  seconds  when  conducting  this  test  or
damage may occur to the pump gland seal components.

Pressure Test

The purpose of this test is to trace a vacuum leak.
With the priming valve CLOSED, connect the pump to a water supply capable of
exerting a pressure of 3.5 / 7.0 bar (50 / 100 lbf / in

2

). This may be achieved either by

fitting an adaptor in the pump casing and then connecting this to a hose, or by using a
hydrant to suction tube adaptor.
To allow air to escape, partially open the delivery valve and apply water pressure. With
the pump casing full of water, close the delivery valve and build up the pressure to 3.5 /
7.0 bar (50 / 100 lbf / in

2

). If there are any leaks, their locations will be shown by the

seepage of water at those points.

Battery Care

Safety

The absorbent glass material (AGM) battery is a sealed unit and requires no fluid top
up during its life.

!

«
...
22
23
24
25
26
...
»

Содержание PowerFlow 12/10









































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerFlow 12/10

Бренд: Jacuzzi Страницы: 8

Бренд: IBO Страницы: 22

Бренд: valent Страницы: 20

Бренд: CIAT Страницы: 35

DRAZICE TO - 20.1

Бренд: Nibe Страницы: 13

RJS-75SS Series

Бренд: red lion Страницы: 32

Бренд: Graco Страницы: 56

Streamline 270MDV

Бренд: Solahart Страницы: 56

Бренд: Reefe Страницы: 12

Бренд: Davey Страницы: 20

Бренд: EBARA Страницы: 28

Бренд: laguna Страницы: 10

Бренд: Ozito Страницы: 8

MULTI-HE Series

Бренд: salmson Страницы: 44

AJ 4 Plus 100/57 AUT

Бренд: T.I.P. Страницы: 20

Бренд: Aquagarden Страницы: 44

Бренд: Morrison Страницы: 23

Бренд: AmeriWater Страницы: 66

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды