GMP QTOPIC-380 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 48

GMP QTOPIC-380 Скачать руководство пользователя страница 16

HOW TO USE CONTROL PANEL

I. "LOADING"(Button for Film Loading & Setting) :

To set the machine initially and to load a film roll.
While "LOADING" button is pressed, roller is rotated and feeder is opened for feeding.

NOTE

: During the machine operation, the function is not activated.

J. "BURST"(Button to operate Upper Bursting Roller) :

To move Bursting Roller to up/downwards.

Press "BURST" button to light on. Then, the Bursting Roller starts to move.
Press the button again and lamp is OFF, the Bursting Roller is stopped to move.

NOTE :

Only in RUN status, the button is activated. In STOP status, the button is not activated.

K. "RUN"(Operation Button) :

To operate the machine. Press "RUN" button to operate roller with engagement.

L. "STOP"(Stop Button) :

Stop the machine operation. Press "STOP" button to stop roller and the rollers are disengaged.

top the machine operation. Press "STOP" button to stop roller and the rollers are disengaged.

M. "BURST SPEED"(Button to operate Lower Bursting Roller in high speed) :

To make the lower bursting roller in high speed during lamination for NYLONEX(NYLON) & PERFEX(PET) films to increase its cutting quality.
Press "BURST SPEED" button and its lamp is ON, the lower bursting roller is rotated in high speed. Then, press the button and the lamp is OFF,
the roller is rotated in normal speed.

16/48

«
...
14
15
16
17
18
...
»

Содержание QTOPIC-380

















































Отзывы:

Нет отзывов