GMP 89915 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 32

GMP 89915 Скачать руководство пользователя страница 7

Page 7

General Machine Products

(KT), LLC

2. Critical points that dramatically affect the operation of the cable blowing

machine.

•

Pressure on the cable should be set as per the instructions.

•

Rollers to be closed at all times when cable is installed into machine.

•

Cord seals in air chamber correctly fitted to provide good sealing.

•

Correct cable seal fitted.

•

Tube fully connected and pressure

-

tested.

•

Tube connecting fittings are suitable for operating at 220 PSI air pressure.

•

Tube clamp securely tightened.

•

Compressor capacity 220 PSI and suitable for size of tube being used.

•

Cable drum must be located directly behind and in line with the blowing machine.

•

Air chamber, drive rollers, cable guides, must be clean and free from debris, sludge, dirt,

water and lubricant.

•

The cable must be hand guided into the blowing machine through a dry clean cloth by the

operator wearing work gloves.

•

Ensure the compressed air supply is not applied to the cable until required amount of ca-

ble has been installed.

•

The counter/display is powered by (2) 9 volt batteries. To maximize battery life, turn dis-

play off by pressing power button on left side of display box when unit is not in use.

«
...
5
6
7
8
9
...
»

Содержание 89915

































Отзывы:

Нет отзывов