GMP 89915 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 32

GMP 89915 Скачать руководство пользователя страница 14

Page 14

General Machine Products

(KT), LLC

TUBE COLLET AND

CLAMP ASSEMBLIES

89923

12mm O.D.

89921

12.7mm O.D.

89928

14mm O.D.

89925

16mm O.D.

89924

18mm O.D.

Loosen the thumb nut, rotate the swing bolt

to open the air box

Insert the top and bottom tube clamps align-

ing the grooved edge to the outside. Tighten

the 4 screws.

Insert the the top and bottom airbox halves

and tighten the screws

Fit the tube into the air box and tube

clamp.

Slide a tube seal, sized for the tubing you

are using, over the end of the tube.

Fit the tube half way or more into the air

box housing as shown in the photo, posi-

tioning the tube seal so that it sits against

the seal face.

Positioning the tube further into the air

box helps prevent the buckling of smaller

fiber.

Place a cable seal sized to the cable you

are blowing in the wide groove.

Preparing the Whisper for the proper duct size

Measure the OD of the duct. Select the corresponding tube collet and clamps

Other tube sizes available –Contact

GMP for information.

Note:

If the seal has a small taper, place the

large side toward the airbox as shown in

the illustration to the right.

«
...
12
13
14
15
16
...
»

Содержание 89915

































Отзывы:

Нет отзывов