GMC DP250LS Скачать руководство пользователя страница 14

Страница: 14 / 16

Trouble shooting

WARNING.

Turn the on/off switch to the off position and unplug the tool from the power supply before performing trouble

shooting procedures.

Trouble shooting

Problem

Cause

Solution

Drill press will not start

Power cord not plugged in

Ensure that the cord is connected to

the power supply

Power fault, fuse or circuit breaker

tripped

Check the power supply

Cord damaged

Use authorised service centre to repair

or replace

Faulty switch

Use authorised service centre to repair

or replace

Faulty motor

Use authorised service centre to repair

or replace the motor

Noisy operation

Incorrect belt tension

Adjust tension as required

Drill bit burns

Incorrect speed

Change speed, refer to the “Changing

the speed” section

Chips not coming out of hole

Retract drill bit frequently to clear holes

Dull drill bit

Resharpen or replace drill bit

Excessive drill bit wobble

Bent drill bit

Replace with new drill bit

Drill bit not properly installed in chuck

Install drill bit properly and ensure it

is secure

Chuck not properly installed

Install chuck properly

Wood splinters under workpiece

No “packing” material below workpiece Use “packers” below the workpiece

Workpiece torn from hand

Workpiece not supported or clamped

properly

Support the workpiece or clamp it

Drill bit binds in workpiece

Improper belt tension

Adjust the belt tension

Содержание DP250LS

















Результаты поиска

Содержание DP250LS

Отзывы:

Похожие инструкции для DP250LS

Бренды по названию

Популярные бренды

GMC DP250LS, Инструкция по эксплуатации

Результаты поиска

Содержание DP250LS

Отзывы:

Похожие инструкции для DP250LS

Бренды по названию

Популярные бренды