Glow-worm Hideaway 70B Скачать руководство пользователя

Страница: 24 / 24

221763A

11 Spare Parts

Because of our constant endeavour for improvement, details may vary slightly from those shown in these instructions.

When ordering spare parts please quote the part number and
description, stating the model and serial number, from the data
label “L”, see diagram 7.1.

If ordering from British Gas also quote the GC number of the part
and appliance.

9014

Diagram 11.1

Key No

Part No

Description

GC No

800001

Gas control valve

*** ***

205749

Injector

*** ***

203414

Pilot burner

312 426

203508

Injector - pilot

395 674

202407

Thermocouple c/w nut

392 850

202415

Thermocouple c/w nut

202571

Thermostat c/w screws

204687

Control knob assy - thermostat

202713

Piezo unit

WW4609

Ignition lead assembly

136 464

202605

Spark electrode

395 720

208302

Sight glass

312 419

212031

“O” ring - gas valve

312 602

Содержание Hideaway 70B

























Результаты поиска

Содержание Hideaway 70B

Отзывы:

Похожие инструкции для Hideaway 70B

Бренды по названию

Популярные бренды

Glow-worm Hideaway 70B, Инструкция по эксплуатации

Результаты поиска

Содержание Hideaway 70B

Отзывы:

Похожие инструкции для Hideaway 70B

Бренды по названию

Популярные бренды