Glow-worm 12hx Скачать руководство пользователя страница 19

Страница: 19 / 52

0020107230_04 - 12/14 - Glow-worm

INSTALLATION

- 19 -

6 Installation Preparation

6.1 Appliance Pack

Please check the contents of packs as shown in diagram 6.1.

The packs are located in the top polystyrene packing.

Remove the carton sleeve and top pack then lift the boiler and
its polystyrene base support out of the lower pack.

6.2 Site Requirements

The boiler mounting wall should be suitable for the weight of the
appliance and be true and

at.

NOTE:

Due to the varied site conditions we do not supply

xings and advise that the installer should supply those which

are suitable.

6.3 Wall Template

Take the wall template from the document pack located within

the top polystyrene packing

and place in the desired position

on the wall, giving due consideration to the required boiler

clearances,

see section 3

, and the

ue you are

tting.

Mark the position of the

ue centre, if

tting a side

ue, extend

the

ue centre line into the corner then 149mm along the

adjacent wall, see diagram 6.2.
For extended side

ues, the

ue hole centre should be

determined by extending the dashed inclined line on the
template to the side wall, then 149mm along the adjacent wall,
see diagram 6.2. This dashed line is drawn at 44mm/metre
(2.5°) rise from the boiler.
To allow for the

ue passing through the wall at this angle a

125mm hole should be drilled irrespective of internal or external

installation.
Remove the wall template whilst drilling the

ue hole.

6.4 Flue Hole Cutting

External access

ue installation can use a 105mm diameter

core drill.
Internal access only

ue installation will need a 125mm

diameter core drill.

NOTE:

The

ue is designed with an internal fall of 44mm/metre

(2.5°), therefore the hole can be drilled horizontally.
If

ue extension pipes are to be used then a core drill size of

125mm is required. This will allow the extension pieces to
slope at 44mm/metre (2.5°) towards the boiler.

14020

Diagram 6.2

Diagram 6.1

14805

Documentation Pack

(not illustrated)

Wall Template, User Instructions,

Installation and Servicing Instructions,

Flue Installation Instructions.

Содержание 12hx





















































Результаты поиска

Содержание 12hx

Отзывы:

Похожие инструкции для 12hx

Бренды по названию

Популярные бренды

Glow-worm 12hx, Установка и обслуживание

Результаты поиска

Содержание 12hx

Отзывы:

Похожие инструкции для 12hx

Бренды по названию

Популярные бренды