manualshive.com logo in svg

Global Hobby Wattage P-51 Reno Racer EP, Инструкции по окончательной сборке

Поделиться
Скачать
Global Hobby Wattage P-51 Reno Racer EP Скачать руководство пользователя страница 5

5

Visit our website at http://watt-age.globalhobby.com for information on other Wattage products

Here's What We Used to Finish Our P-51 Reno Racer EP:

IMPORTANT

The part numbers listed for the Hitec receiver, Cirrus servos and Wattage ESC are compatible with Hitec and JR (receiver
is compatible with Hitec only) radio control systems.  These items are also available with connectors that are compatible
with Futaba and Airtronics radio control systems.  (Micro 555 receiver is also available for Airtronics, Futaba and JR radio
systems.)

When you purchase the Hitec Micro 555 receiver, you must also purchase a Hitec brand crystal compatible with the
receiver.  The crystal must also be on the same frequency as your transmitter.  Note that the Micro 555 receiver uses a dual
conversion FM Hitec crystal.

P/N 759118

Hitec 555 Micro Receiver

Hitec Dual Conversion FM RX Crystal

P/N 444052

Cirrus CS-10 Super-Micro Servos (3)

P/N 128484

Wattage IC-15A Micro ESC

P/N 128538

Wattage 8 Cell 800Mah 5/4AAA NiMH Flight Battery

P/N 130103

Wattage 7-8 Cell AC/DC Peak Charger

P/N 625085

Dean's Ultra-Plug Battery Connector

P/N 131175

Wattage 14 Gauge Hi-Temp Silicon Wire

3M 3/4" Wide Clear Plastic Tape - Available at Most Hardware Stores

❑

Kwik Bond 5 Minute Epoxy # 887560

❑

Kwik Bond Thin C/A # 887500

❑

Kwik Bond Thick C/A # 887510

❑

Wilhold Silicon Sealant # 335407

❑

Pacer Z-42 Threadlocker # 339162

❑

Lightweight Oil or Vaseline

❑

# 0 Phillips Head Screwdriver

❑

# 1 Phillips Head Screwdriver

❑

.050 Hex Wrench

❑

Magnum Z-Bend Pliers # 237473

❑

Wire Cutters

❑

Needle Nose Pliers

❑

Adjustable Wrench

❑

Excel Modeling Knife # 692801

❑

Scissors

❑

Electric or Hand Drill

❑

Assorted Drill Bits

❑

Ruler

❑

Pencil

❑

Masking Tape

❑

220 Grit Sandpaper w/Sanding Block

❑

Paper Towels

❑

Rubbing Alcohol

❑

NHP Epoxy Mixing Sticks # 864204

❑

NHP Epoxy Mixing Cups # 864205

❑

K&S 30 Watt Soldering Iron # 598120

❑

Heat-Shrink Tubing

❑

Solder

SECTION 2:  TOOLS AND SUPPLIES REQUIRED

To break in the motor you will need:

❑

Emerald Performance Plus Motor Spray # 340186

❑

Trinity Motor Break In Drops # 840768

❑

Rubber Bands

Note:  To minimize current loss, we suggest
soldering the motor wires directly to the ESC.

We also suggest replacing the stock Tamiya
connector that is likely preinstalled on your
ESC and flight battery with a more efficient
Dean's Ultra-Plug battery connector.

Содержание Wattage P-51 Reno Racer EP













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды