manualshive.com logo in svg

Global Hobby Wattage P-51 Reno Racer EP, Инструкции по окончательной сборке

Поделиться
Скачать
Global Hobby Wattage P-51 Reno Racer EP Скачать руководство пользователя страница 41

41

Visit our website at http://watt-age.globalhobby.com for information on other Wattage products

SECTION 18:  FLYING THE P-51 RENO RACER EP

The P-51 Reno Racer EP can take off from the ground or be hand-launched.  We recommend ground take-offs only from
hard smooth surfaces.

Taking Off from the Ground

With the airplane pointing into the wind, apply full power and feed in right rudder to keep the airplane tracking straight as it
rolls down the runway.  Once sufficient airspeed has been reached, gently apply up elevator to lift the airplane off the
ground.  Climb out straight ahead in a shallow climb to build up speed.  Do not make any steep turns right after take-off or
you may stall the airplane.

Hand Launching

Hand Launching should always be done into the wind.

To hand-launch the airplane, gently grasp the fuselage directly behind the wing using  your thumb and forefingers.  Hold the
airplane above shoulder level and turn on the motor to full power.  With the motor running at full power, firmly throw the
airplane straight ahead and level.  Do not throw it up at an angle or throw it too hard or out of control.  Let the airplane fly
straight and level to pick up airspeed, then climb to your desired altitude.  Be careful not to climb too steeply after hand-
launching or you could stall the airplane.

In the Air

In the air the P-51 Reno Racer EP is smooth and predictable.  At full power, the airplane is fast and responsive to control
inputs, and handles light winds with ease.  It "grooves" around corners and is rock-steady while "up on the wing."  Loops,
rolls, Immelmann turns, cuban eights, spins and other aerobatics are completed without much effort.  You will find the
airplane tracks very true and stays where you put it.

Landing

Landings should always be done into the wind.

Prepare for landing by reducing power and making a shallow turn into the wind.  (With power off we strongly suggest
avoiding high-banked turns.)  With the airplane on final approach it will begin to slow down and descend.  With the
airplane descending, apply small amounts of up elevator to slow the airplane's speed.  Just before touch-down, turn the
motor off and let the airplane settle near the ground.  Flair just before touch-down and you will be rewarded with a soft
landing.  As always, when landing, be careful not to over-control.  Over-controlling leads to excessive oscillations which
don't make for good landings.

Содержание Wattage P-51 Reno Racer EP













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды