manualshive.com logo in svg

Global Hobby Wattage P-51 Reno Racer EP, Инструкции по окончательной сборке

Поделиться
Скачать
Global Hobby Wattage P-51 Reno Racer EP Скачать руководство пользователя страница 37

37

Visit our website at http://watt-age.globalhobby.com for information on other Wattage products

❑

Mount the ESC to the fuselage side, as far away from

the receiver as possible.  Use a small piece of double-sided
tape to hold it in place.

☞

Mounting the ESC as far away from the receiver as

possible will reduce the chance of radio interference.

Step 4:  Installing the Flight Battery

❑

Set the flight battery onto the battery tray and slide it

through the nylon tie-down strap.

❑

Hold the flight battery in place and pull the tie-down strap

to tighten the flight battery down firmly.

☞

To remove the flight battery, push the tab on the tie-down

strap to loosen it enough to pull the flight battery free.

☞

The location of the flight battery shown above is only approximate.  You may need to move it fore or aft to balance the

airplane when that is done in the next section.

❑

Using a modeling knife, carefully cut a 1/2" diameter air-exit hole in the bottom of the fuselage, about 1" behind the

back of the wing saddle.  This hole, along with the air-intake hole in the front of the fuselage, will allow hot air to exit the
fuselage, keeping the flight battery from overheating.

❑

If your ESC has an on/off switch, mount it to the fuselage side in front of the wing saddle.

☞

We don't suggest mounting the switch in the radio compartment, because it might interfere with the aileron servo when

the wing is mounted.

Step 5:  Applying the Decals

❑

Working with one decal at a time, use a pair of scissors to carefully cut out the decal along its outer  edges.

☞

Notice that next to each large decal there is printed its location on the airplane.

❑

Remove the protective backing from the decal and apply the decal to the airplane.  (Use the box cover photos to

position the decals.)  Lightly rub the decal with a soft cloth to remove any trapped air from beneath it.

☞

If any air bubbles form in the decal you can "prick" the bubble with a straight pin to release the air.

❑

Repeat the steps above to apply the remaining decals.  Rub each decal down thoroughly to adhere it into place.

Содержание Wattage P-51 Reno Racer EP













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды