PG 22
PG 23
Start of dishwasher
The following should be checked before starting the dishwasher:
1. Whether the dishwasher is level and fixed
2. Whether the inlet valve is opened
3. Whether there is leakage at the connections of the conducts
4. Whether the wires are tightly connected
5. Whether the power is switched on
6. Whether the inlet and drain hoses are knotted
7. All packing materials and printings should be taken out from the dishwasher
Attention
After installation, please put this manual into the bags of printings.
The content of this manual is very helpful to the users.
9. TROUBLESHOOTING TIPS
ERROR CODES
When some malfunctions happen, the appliance will display error codes to warn you.
Codes
Meanings
Possible Causes
Water drainage malfunction
E1
E2
E3
E4
E5
E6
E7
Door open
Water inlet
Water drainage
Temperature sensor
Overflow/leakage
Water leakage
Heating element
Water inlet malfunction
Temperature sensor malfunction
The door is opened when the
dishwasher is operating
Overflow occurs/Water leakage occurs
Water leakage occurs
Abnormal heating
WARNING!
If overflow occurs, turn off the main water supply before calling a service. If there is water in the base pan because of an overfill
or small leak, the water should be removed before restarting the dishwasher.
interior
Stained tub
Make sure that the detergent is the one without colorant.
Detergent with
colorant was used
flatware
Dishes and
not clean
Select a stronger programme.
Make sure that the action of the detergent dispenser
and spray arms are not blocked by large dishware.
Spots and
filming on
Improper program
Improper basket
loading
glasses and
flatware
1 Extremely hard
water
2 Low inlet
of detergent
temperature
3 Overloading the
dishwasher
4 Improper loading
5 Old or damp
powder detergent
6 Empty rinse agent
dispenser
7 Incorrect dosage
the cycle. If the vinegar does not work: Repeat
as above, except use 1/4 cup (60 ml)of citric acid
crystals instead of vinegar.
Problem
doesn't run
Dishwasher
Drain pump
doesn't stop
Noise
Suds in
the tub
Possible Causes
Use only the special dishwasher detergent to avoid
suds.If this occurs, open the dishwasher and let suds
evaporate. Add 1 gallon of cold water to the tub. Close
and latch the dishwasher, then start the "soak" wash
cycle to drain out the water... Repeat if necessary.
To remove spots from glassware:
1 Take out all metal utensils out of the dishwasher.
2 Do not add detergent.
3 Choose the longest cycle.
4 Start the dishwasher and allow it to run for about
18 to 22 minutes, then it will be in the main wash.
5 Open the door to pour 2 cups of white vinegar
into the bottom of the dishwasher.
6 Close the door and let the dishwasher complete
What To Do
Spilled rinse agent
Always wipe up rinse agent spills immediately.
not turned on
Power supply is
Fuse blown, or the
circuit breaker acted
Water pressure
is low
Overflow
Utensils are not
secure in the
Some audible
sounds are normal
The system is designed to detect an overflow. When it
does, it shuts off the circulation pump and turns on the
drain pump.
baskets or
has dropped into
something small
the basket
Motor hums
Improper detergent
.
Dishwasher has not been used regularly. If you do not
use it often, remember to set it to fill and pump out
every week, which will help keep the seal moist.
Check that the water supply is connected properly and
the water is turned on.
Sound from detergent dispenser opening.
Replace fuse or reset circuit breaker. Remove any other
appliances sharing the same circuit with the dishwasher.
Make sure the dishwasher is turned on and the door is
closed securely. Make sure the power cord is properly
plugged into the wall socket.
Before Calling for Service
Reviewing the charts on the following pages before calling for service.
Ensure everything is secured in the dishwasher.
