PG 20
PG 21
3. Position the dishwasher on a level and sturdy floor. If the floor is uneven, the front feet of the appliance may be adjusted
until it reaches a horizontal position (the angle of inclination must not exceed 2 degrees). If the appliance is levelled
correctly, it will be more stable and much less likely to move or cause vibrations and noise while it is operation.
Connecting the water and electricity supplies
Connection to the water and electricity supplies should only be performed by a qualified technician.
The dishwasher should not stand on top of the water hoses or the electricity supply cable The appliance must be connected to the
water supply network using new hose sets. Do not use old hose sets.
Connecting the water inlet hose
Connect the cold water supply hose to a threaded 3/4(inch) connector
and make sure that it is fastened tightly in place. If the water pipes are
new or have not been used for an extended period of time, let the water
run to make sure that the water is clear and free of impurities. If this
precaution is not taken, there is a risk th
at the water inlet can get blocked
and the appliance could be damaged.
Connecting the water outlet hose
Fit the drainage hose of your machine to the drainage pipe without bending.
If the length of the hose is not sufficient, apply to the authorized service for an
extension made from the same material as the original. Remember that the
length of the hose should not exceed 4meters even when with an
extension.
If the drainage hose is longer the 4 m. the dishes will not be cleaned properly.
Secure your hose firmly to the drainage pipe to avoid it coming off
during the washing process.
Electrical connection
Before inserting the plug into the electrical socket, make sure that:
• the socket is earthed and complies with current regulations;
• the socket can withstand the maximum load of the appliance, which is indicated on the data plate located on the inside of the
door(see description of the appliance);
• the power supply voltage falls within the values indicated on the data plate on the inside of the door;
• the socket is compatible with the plug of the appliance. If this is not the case, ask an authorised
• technician to replace the plug (see assistance); do not use extension cables or multiple sockets.
• Once the appliance has been installed, the power supply cable and the electrical socket should be easily accessible.
• The cable should not be bent or compressed.
• If the power supply cable is damaged, it must be replaced by the manufacturer or its Technical
• Assistance Service in order to prevent all potential hazards.(See Assistance)
• The company shall not be held responsible for any incidents that occur if these regulations are not observed.
Advice regarding the first wash cycle
After the appliance has been installed, immediately before running the first wash cycle, completely fill the dispenser of Rinse Aid
(see Rinse aid).
Positioning the Appliance
Position the appliance in the desired location. The back should rest against the wall behind it, and the sides, along the adjacent
cabinets or wall. The dishwasher is equipped with water supply and drain hoses that can be positioned to the right or the left to
facilitate proper installation.
Leveling the Appliance
Once the appliance is positioned, adjust the feet (screwing them in or out) to adjust the height of the dishwasher, making it level.
In any case, the appliance should not be inclined more than 2.
NOTE: The maximum adjustment height of the feet is 20 mm.
How to Drain Excess Water From Hoses
If the sink is 1000mm higher from the floor, the excess water in hoses cannot be drained directly into the sink. It will be necessary
to drain excess water from hoses into a bowl or a suitable container that is held outside and lower than the sink.
Water Outlet
Connect the water drain hose. The drain hose must be correctly fitted to avoid water leaks.
Ensure that the water inlet hose is not kinked or squashed.
Extension Hose
If you need a drain hose extension, observe to use a similar drain hose..
It must be no longer than 4 metres; otherwise the cleaning effect of the dishwasher could be reduced.
Syphon Connection
The waste connection must be at a height of between 50cm (minimum) and 100cm (maximum) from the bottom of the dish. The
water drain hose should be fixed by a hose clip.
