background image

Page 10

COmmISSIONINg

COmmISSIONINg

TORRENT DIRECT

Direct Electric Model

Ensure that the thermal store cistern is filled with water to the water level mark inside 
the feed cistern and the ballvalve (if fitted) is set correctly. 

Switch  the  immersions  on  and  allow  the  store  to  heat  up  to  its  full  temperature 
(around 77°C).

When  the  store  has  been  fully  charged  open  the  nearest  hot  tap  and  check  the 
mixing valve at the Torrent unit is delivering the desired temperature.  (Note:- the 
mixing valve is factory set around 55°C  ±5°).  Adjust if necessary to suit individual 
requirements.  

ELECTRICIAN/INSTALLER

PLEASE NOTE WATER AT THE HOT TAP DOES NOT INDICATE THAT THE CYLINDER 
IS FULL.  
CHECK THAT THERE  IS WATER  IN THE  FEED  AND  EXPANSION TANK  BEFORE 
SWITCHINg ELECTRICITY ON TO THE ImmERSION HEATERS.  “DRY FIRINg” THE 
ELEmENTS WILL CAUSE PREmATURE FAILURE WHICH IS NOT COVERED BY OUR 
NORmAL WARRANTY.

TORRENT INDIRECT

•  Ensure that the thermal store cistern is filled with water to the water level mark  
 

inside the feed cistern and the ballvalve (if fitted) is set correctly.

•  Ensure  that  the  store  thermostat  is  set  at  70°C.    Check  the 

boiler  control 

 

thermostat is set at maximum

.

  When the boiler switches off check that 

 

the  store  thermostat  is  not  calling  for  heat  and  is  satisfied.   The  boiler 

 

may cycle two or three times to achieve this.

 

•  When  the  store  has  been  fully  charged  open  the  nearest  hot  tap  and  check  
 

the  mixing  valve  at  the Torrent  unit  is  delivering  the  desired  temperature.  

 

(Note:- the mixing valve is factory set around 55°C  ±5°).  Adjust if necessary to 

 

suit individual requirements.

 

It  is  essential  that  the  system  functions  properly  for  optimium  performance.  

 

To achieve this, the system should be commissioned in accordance with good 

 

practice  and  generally  in  accordance  with  the  requirements  of  BS  6798,  BS 

 

5449 and BS 7593: 199.  

•  Fill the system and flush cold.

•  Refill the system.

•  Add a cleanser such as Fernox Superfloc or Sentinel X300 to ensure that  

flux residues and installation debris are removed from the system.  

When  

determining the quantity of cleanser required, on open vented systems,  
be sure to allow for the increased volume of water in the primary circuit  
due to the thermal store.

•  Commission the boiler.

•  If the boiler is range rated, then adjust to the specified design heat input.

  

•  Set the pump between boiler and Torrent to a temperature difference across 
 

the boiler  between 8 - 11

o

C.

•  To  ensure  full  cleansing,  circulation  to  all 

parts of the system should continue for a 
minimum of 1 hour.  

•  Flush the system hot having checked that 
 

there  is  no  overflow  when  the  system 

 

is up to temperature.

•  Refill the system.

Although the standard Torrent has no special 
water  treatment  requirements,  the  radiators 
and  other  parts  of  the  circuit  will  benefit 
from the application of a corrosion and scale 
inhibitor, such as Fernox MBI or Sentinel X100.  

When determining the quantity of inhibitor 
required, on open vented systems, be sure 
to allow for the increased volume of water 
in  the  primary  circuit  due  to  the  thermal 
store.
Set the boiler to maximum.

With  the  central  heating  system  off,  let 
the  system  heat  up  (1.5  hours  -    hours 
approximately).  

•  Check  that  the  space  heating  system 
 

controls  are  functioning  correctly  i.e. 

 

CLOCK AND ROOm THERmOSTAT.

•  Switch off space heating system.

•  Ensure that the store thermostat is set to 
 

70°C.

•  Ensure that the boiler thermostat is set to 
 

maximum.

•  Establish that the temperature difference 
 

between the flow and return at the boiler 

 

is not more than 11°C.

 

If  it  is  more  than  11°C,  and  the  pipes 

 

are  sized  correctly,  then  check  that 

 

in accordance with good practice, air 

 

air vents have been fited at high points.

 

Increase  the  pump  setting  if  necessary.  

 

Check for obstructions in the pipework.

Final Setting of Store Thermostat

Ensure that the heating clock is set to “off”.
Refire the boiler by running a little water, wait 
for the boiler to switch off. Check that there is 
no live supply from the store thermostat and 
the stat has been satisfied.

Содержание Torrent T144 DE





















Отзывы: