background image

Page 55

TERMS AND C

ONDITIONS

(f )  Components of our products other than Storage Vessels and Integral Pipework.  
We will either extend to the purchaser the same terms of warranty as we are given by the manufacturer of the 
component or if the manufacturer does not give any warranty, replace free of charge any component which 
becomes defective within two years after the date of the delivery by us and is returned to us at the purchaser’s 
expense but we shall not meet the cost of removal or shipping or return of the component or any other cost 
charges or damages incurred by the purchaser.
If the appliance manufactured by Gledhill incorporates a factory fitted scale inhibitor then during the period 
of three years from the date of delivery Gledhill will replace, free of charge, any plate heat exchanger fitted in 
the appliance as original equipment in which scale formation occurs that materially reduces the effectiveness 
of the plate heat exchanger.  This guarantee does not extend to any other component installed within the 
Gledhill appliance or elsewhere in the Purchasers domestic water system.
(g) General
In the case of goods manufactured solely in accordance with our specification and designs and in respect 
of any installation work carried out by or on our behalf, our entire liability and the purchaser's sole remedies 
(subject to (a) - (f ) above) and shall be as follows:
(a) we accept liability for death or personal injury to the extent that it results from our negligence that of our 
employees agents or subcontractors.
(b) subject to paragraph (d) below, we accept liability for direct physical damage to tangible property to the 
extent that such damage is caused by our negligence that of our employees agents or subcontractors.
(c) our total liability to the purchaser over and above any liability to replace under (1 - 4) above (whether in 
contract or in tort including negligence) in respect of any one cause of loss or damage claimed to result from 
any breach of our obligations hereunder, shall be limited to actual money damages which shall not exceed 
£20,000 provided that such monetary limit shall not apply to any liability on the part of ourselves referred to 
in paragraph (a) above.
(d) except as provided in paragraph (a) above but otherwise notwithstanding any provision herein contained 
in no event shall we be liable for the following loss 
or damage howsoever caused and even if foreseeable by us or in our contemplation :-
(i) economic loss which shall include loss of profits, business revenue, goodwill or anticipated savings.
(ii) damages in respect of special indirect or consequential loss or damage (other than death, personal injury 
and damage to tangible property).
(iii) any claim made against the purchaser by any other party
(save as expressly provided in paragraph (b) above).
(e) except in respect of our liability referred to in paragraph (a) above no claim may be made or action brought 
(whether in contract or in tort including negligence) by the purchaser in respect of any goods supplied by us 
more than one year after the date of the invoice for the relevant goods.
(f ) nothing in these Conditions shall confer on the purchaser any rights or remedies to which the purchaser 
would not otherwise be legally entitled.
10. LOSS OR INJURY
Notwithstanding any other provision contained herein the Purchaser's hereby agree to fully indemnify us 
against any damages losses costs claims or expenses incurred by us in respect of any claim brought against 
us by any third party for :-
(a) any loss injury or damage wholly or partly caused by any goods supplied by us or their use.
(b) any loss injury or damage wholly or partly caused by the defective installation or sub-standard workman-
ship or materials used in the installation of any goods supplied by us.
(c) any loss injury or damage in any way connected with the performance of this contract.
PROVIDED that this paragraph (6) will not require the Purchaser to indemnify us against any liability for our 
own acts of negligence or those of our employees agents or sub-contractors.
FURTHER in the case of goods supplied by us which are re-sold to and installed by a third party by the Pur-
chaser it will be the sole responsibility of the Purchaser to test the goods immediately after their installation 
to ensure that inter alia they are correctly installed and are in proper working order, and are not likely to cause 
any loss injury or damage to any person or property.
11. VARIATION OF WARRANTY AND EXCLUSION
Should our warranty and exclusion be unacceptable we are prepared to negotiate for variation in their terms 
but only on the basis of an increase in the price to allow for any additional liability or risk which may result 
from the variation.
Purchasers are advised to insure against any risk or liability which they may incur and which is not covered 
by our warranty.
12. RISK AND RETENTION OF TITLE
(a) goods supplied by us shall be at the Purchaser's risk immediately upon delivery to the Purchaser or into 
custody on the Purchaser's behalf or to the Purchaser's Order.  The Purchaser shall effect adequate insurance 
of the goods against all risks to the full invoice value of the goods, such insurance to be effective from the time 
of delivery until property in the goods shall pass to the Purchaser as hereinafter provided.
(b) property in the goods supplied hereunder will pass to the Purchaser when full payment has been made 
by the Purchaser to us for :-
(i) the goods of the subject of this contract.
(ii) all other goods the subject to of any other contract between the Purchaser and us which, at the time of 
payment of the full price of the goods sold under this contract, have been delivered to the Purchaser but not 
paid for in full.
(c) until property in the goods supplied hereunder passes to the Purchaser in accordance with paragraph 
(2) above.
(i) the Purchaser shall hold the goods in a fiduciary capacity for us and shall store the same separately from 
any other goods in the Purchaser's possession and in a manner which enables them to be identified as our 
goods.
(ii) the Purchaser shall immediately return the goods to us should our authorised representative so request.  
All the necessary incidents associated with a fiduciary relationship shall apply.
(d) the Purchaser's right to possess the goods shall cease forthwith upon the happening of any of the following 
events, namely :-
(i) if the Purchaser fails to make payment in full for the goods within the time stipulated in clause 4 hereof.
(ii) if the Purchaser, not being a company, commits any act of bankruptcy, makes a proposal to his or her creditors 
for a compromise or does anything which would entitle a petition for a Bankruptcy Order to be presented.
(iii) if the Purchaser, being a company, does anything or fails to do anything which would entitle an administrator 
or an administrative receiver or a receiver to take possession of any assets or which would entitle any person 
to present a petition for winding up or to apply for an administration order.

(e) the Purchaser hereby grants to us an irrevocable licence to 
enter at any time any vehicle or premises owned or occupied 
by the Purchaser or in the possession of the Purchaser for 
the purposes of repossessing and recovering any such goods 
the property in which has remained in us under paragraph 
(2) above.  We shall not be responsible for and the Purchaser  
will  indemnify  us  against  liability  in  respect  of  damage 
caused  to  any  vehicle  or  premises  in  such  repossession 
and removal being damaged which it was not reasonably 
practicable to avoid.
(f )  notwithstanding  paragraph  (3)  hereof  and  subject  to 
paragraph (7) hereof, the Purchaser shall be permitted to sell 
the goods to third parties in the normal course of business.  
In this respect the Purchaser shall act in the capacity of our 
commission agent and the proceeds of such sale :-
(i) shall be held in trust for us in a manner which enables 
such proceeds to be identified as such, and :
(ii) shall not be mixed with other monies nor paid into an 
overdrawn bank account.
We, as principal, shall remunerate the Purchaser as commis-
sion agent a commission depending upon the surplus which 
the Purchaser can obtain over and above the sum, stipulated 
in this contract of supply which will satisfy us.
(g) in the event that the Purchaser shall sell any of the goods 
pursuant to clause (6) hereof, the Purchaser shall forthwith 
inform us in writing of such sale and of the identity and address 
of the third party to whom the goods have been sold.
(h) if, before property in the goods passes to the Purchaser 
under paragraph (2) above the goods are or become affixed 
to any land or building owned by the Purchaser it is hereby 
agreed and declared that such affixation shall not have the 
effect  of  passing  property  in  the  goods  to  the  Purchaser.  
Furthermore if, before property in the goods shall pass to 
the  Purchaser  under  paragraph  (2)  hereof,  the  goods  are 
or become affixed to any land or building (whether or not 
owned by the Purchaser), the Purchaser  shall:-
(i)  ensure  that  the  goods  are  capable  of  being  removed 
without material injury to such land or building.
(ii) take all necessary steps to prevent title to the goods from 
passing to the landlord of such land or building.
(iii) forthwith inform us in writing of such affixation and of 
the address of the land or building concerned.
The Purchaser warrants to repair and make good any damage 
caused by the affixation of the goods to or their removal 
from any land or building and to indemnify us against all 
loss damage or liability we may incur or sustain as a result 
of affixation or removal.
(i) in the event that, before property in the goods has passed 
to the Purchaser under paragraph (2) hereof, the goods or any 
of them are lost, stolen, damaged or  destroyed :-
(i)  the  Purchaser  shall  forthwith  inform  us  in  writing  of 
the  fact  and  circumstances  of  such  loss,  theft,  damage  or 
destruction.
(ii) the Purchaser shall assign to us the benefit of any insur-
ance claim in respect of the goods so lost, stolen, damaged 
or destroyed.
13. NON-PAYMENT
If the Purchaser shall fail to make full payment for the goods 
supplied hereunder within the time stipulated in clause 4 
hereof or be in default of payment for any other reason then, 
without prejudice to any of our other rights hereunder, we 
shall be entitled to stop all deliveries of goods and materials 
to the Purchaser, including deliveries or further deliveries of 
goods under this contract.  In addition we shall be entitled 
to terminate all outstanding orders.
14. RISK
All goods sold by us shall be at the sole risk of the Purchaser
from the date of despatch by us of the invoice for their price.
15. VALUE ADDED TAX
All  prices  quoted  are  exclusive  of Value  Added Tax  which 
will be charged at the rate ruling at the date of despatch 
of invoice.
16. TRADE SALES ONLY
We are only prepared to deal with those who are not consum-
ers within the terms of the Unfair Contract Terms Act 1977, 
the Sale of Goods Act 1979 and the Supply of Goods and 
Services Act 1982.  Accordingly any person who purchases 
from us shall be deemed to have represented that he is not 
a consumer by so purchasing.
17. JURISDICTION
The agreement is subject to English/Scottish law and any 
dispute  arising  hereunder  shall  be  settled  in  accordance 
therewith dependent upon the location.

Содержание BMA 240 SP-SOL

























































Отзывы: