Girard Systems GC154 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 12

background image

Page 9 of 12

PROGRAMMING TO A MOTION SENSOR

First the Motion sensor will need to be prepared for programming by carrying out the

following procedure.

Remove the 2 small

Phillips screws which

secure the motion

sensor to the mounting

bracket. The base of

the module is

magnetized so will

need to be gently lifted

off.

Fig.1

Then turn it over.

Fig.2

«
...
7
8
9
10
11
...
»

Содержание GC154













Отзывы:

Нет отзывов

Похожие инструкции для GC154

Бренд: K&K Страницы: 6

Бренд: 7bit Страницы: 2

Бренд: Jafar Страницы: 15

Бренд: Danfoss Страницы: 37

Бренд: Daikin Страницы: 44

Бренд: Easy-Laser Страницы: 84

Бренд: Easy Heat Страницы: 4

Бренд: Eaton Страницы: 288

Бренд: RADEMACHER Страницы: 68

Бренд: Daruifuno Страницы: 24

Бренд: K&K Страницы: 10

WisBlock RAK19012

Бренд: RAK Страницы: 12

Бренд: Cypress Semiconductor Страницы: 36

Бренд: Festo Страницы: 14

Бренд: Daikin Страницы: 8

Бренд: Watts Страницы: 12

AWH18QD-D3DNA3G/I

Бренд: AC Pro Страницы: 48

Бренд: CompuSTAR Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды