Girard Systems 98GC229 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 11

background image

Page 4 of 11

PRODUCT DESCRIPTION

The 98GC229 is a Single channel RF transmitter, powered by two 3v Lithium batteries

(CR2032) designed to control a single Awning by means of three push buttons. IN,

STOP and OUT. As displayed in the picture below.

The faceplate can be removed easily by holding the module at the left and right edges

firmly in one hand and push the STOP button with two fingers of your other hand. The

picture below shows how the batteries must be inserted.

«
...
2
3
4
5
6
...
»

Содержание 98GC229












Отзывы:

Нет отзывов

Похожие инструкции для 98GC229

Бренд: Quick Страницы: 28

Бренд: IBM Страницы: 2

Бренд: United Electric Controls Страницы: 6

DMS-1250 Series

Бренд: D-Link Страницы: 38

Бренд: Thinklogical Страницы: 27

Бренд: N-Tron Страницы: 5

Бренд: LevelOne Страницы: 17

Бренд: DeLOCK Страницы: 8

Бренд: Optex Страницы: 2

Бренд: Hall Research Technologies Страницы: 9

Бренд: Black Box Страницы: 31

Бренд: QSFPTEK Страницы: 8

TNS5000D Series

Бренд: 3onedata Страницы: 3

Бренд: LINK-MI Страницы: 9

RPT-2012/P-4F-T-1 Series

Бренд: Subject Link Страницы: 2

Бренд: IOGear Страницы: 12

Бренд: HighSecLabs Страницы: 4

Бренд: ENSIM SENSORS Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды