background image

 

 

 

 

 

Page 11 of 11

 

 

Note; When carrying out this part of the procedure each step must be 

executed within 10 seconds of the previous one or the module will revert to 

factory settings. It is highly recommended that you read and understand the 

following sequence before attempting to execute it. 

 

1)

 

Supply power to the Motor controller. (The GC1146C will emit a soft beep) 

 

2)

 

Using an appropriate tool press the P2 button on the back of the Handset 

TWICE. ( The GC1146C will Beep with each press) 

 

3)

 

Press the P2 button on the wall switch ONCE (The GC1146C will beep again) 

 

4)

 

Press the IN button on the wall switch and verify that the awning moves in the 

desired direction.   

 

If the awning extends at this point instead of retracting, press the STOP button 

immediately, then remove the power supply to the motor controller for at least 10 

seconds.  

Next repeat steps 1, 2 and 3 above then press the OUT button on the wall switch to 

complete the programming procedure. 

Ensure that the awning responds correctly to the wall switch by pressing the OUT, 

STOP and IN buttons alternately.  

 

For queries or assistance with programming any of your G-Link devices 

please call Girard Systems TOLL FREE on 800–382–8442 between 7:30am 

and 3:30pm P.S.T. 

 

 

  

Содержание 98GC229












Отзывы: