background image

Wireless remote control, 2-gang, Wireless remote control, 4-gang

7

Disposal of batteries

Remove empty batteries immediately and dispose of in an environmentally friendly
manner. Do not throw batteries into household waste. Consult your local authorities
about environmentally friendly disposal. According to statutory provisions, the end

consumer is obligated to return used batteries.

8

Technical data

Rated voltage

DC 3 V

Battery type

1×Lithium CR 2450N

Ambient temperature

-5 ... +45 °C

Degree of protection

IP20

Dimensions L×W×H

55×40.5×15 mm

Radio frequency

868.0 ... 868.6 MHz

Transmission capacity

max. 20 mW

Transmitting range in free field

typ. 100 m

Receiver category

2

9

Parameter list

The device parameters can be changed with the eNet server:

Device and channels

Parameter name

Setting options, Basic setting

Explanations

Function

Rocker, Other modes, Unused
Basic setting: Rocker

Rocker
The channel works as a chan-
nel button. Setting is always
made in pairs.

Other modes
The channel works as a scene
button. Setting is always made
in pairs.

Unused
The channel is not displayed
in the eNet SMART HOME
app and is disabled for use in
the commissioning interface.

6 / 8

32582432

10867219

18.12.2019

Содержание 5352 10









Отзывы: