Gima OXY-50 Скачать руководство пользователя страница 19

 

 

16 

 

 

 

11. DISPOSAL 

The product must not be disposed of along with other domestic waste. The users must dispose of this 

equipment  by  bringing  it    to  a  specific  recycling  point  for  electric  and  electronic  equipment.  For 

further information on recycling points contact the local authorities, the local recycling center or the 

shop  where  the  product  was  purchased.  If  the  equipment  is  not  disposed  of  correctly,  fines  or 

penalties may be applied in accordance with the national legislation and regulations. 

 

12. GIMA WARRANTY CONDITIONS 

Congratulations for purchasing a GIMA product. This product meets high qualitative standards both 

as  regards  the  material  and  the  production.  The  warranty  is  valid  for  12  months  from  the  date  of 

supply of GIMA. During the period of validity of the warranty, GIMA will repair and/or replace free 

of  charge  all  the  defected  parts  due  to  production  reasons.  Labor  costs  and  personnel  traveling 

expenses  and  packaging  not  included.  All  components  subject  to  wear  are  not  included  in  the 

warranty.  The  repair  or  replacement  performed  during  the  warranty  period  shall  not  extend  the 

warranty. The warranty is void in the following cases: repairs performed by unauthorized personnel 

or with non-original spare parts, defects caused by negligence or incorrect use. GIMA cannot be held 

responsible  for  malfunctioning  on  electronic  devices  or  software  due  to  outside  agents  such  as: 

voltage changes, electro-magnetic fields, radio interferences, etc. The warranty is void if the above 

regulations  are  not  observed  and  if  the  serial  code  (if  available)  has  been  removed,  cancelled  or 

changed. The defected products must be returned only to the dealer the product was purchased from. 

Products sent to GIMA will be rejected. 

 

 

 

 

 

 

0123 

 

  Contec Medical Systems Co., Ltd. - 066004 Qinhuangdao, Hebei Province - P.R.C. 

 

  Shanghai  International  Trading  Corp.  GmbH  (Hamburg)  -  Eiffestrasse  80  -  20537 

Hamburg – Germany 

 

 

 

 

 

Rev. 1.10.10 

Содержание OXY-50




















Отзывы: