5. Panel Lock Setting:
At the corresponding furnace press “Panel lock” key to lock all settings at working mode or Timer mode.
Under lock status,the unit would not respond to any key press except the “On/Off” key. Press and hold
this key for 3 seconds to unlock “Lock” status.
1) Clean the unit after it is completely cooled down.
2) Remove the power plug prior to cleaning the unit. Do not use any caustic cleaning agents and make
sure that water does not penetrate inside the unit.
3) Never immerse the unit, cable or the plug into water .
4) Wipe off the glass cooker with a damp cloth or use a mild, non-abrasive soap solution.
5) Do not use any oil based cleansing products in order not to damage the plastic parts or the casing/oper-
Single Ring
Double Ring
400
1
2
3
4
5
6
7
8
9
500
600
600
700
800
1000
1100
1400
700
1000
1400
1400
1400
1400
1700
2000
2800
Please see the details in the following sheet.
●
Press “+” or “-” key when the unit is on standby mode, the hot indicator will be lighted up and the
LED display will show “5” which means the power level is 5 with double rings.
●
Press “Heat zone” key once, you can switch between inner ring and outer ring. The LED display
will show “8”, means the unit is working at power level 8 under the inner ring mode.
●
Press “Heat zone” key again, you can change to outer ring. The LED display will show “8”, means
the unit is working at power level 8 under the outer ring mode.
●
Press “Heat zone” key third time, you can switch back to double ring mode. The LED display will
show “5”, means the unit is working at power level 5 under double rings mode.
●
User can press “+” or “-” key to adjust the desired power level. There are 9 power levels in total
from 1 to 9.
4. Timer Setting:
●
Press the “Timer” key to activate the timer function. The LED display shows “30” indicating the
default timer setting is 30 minutes.
●
Press “+” key to increase the time, and press “-” key to decrease the time. User can press “+”or “-”
key to set for the desired time from 00 minute to 99 minutes.
●
If press and hold “+” or “-” key, the timer can increase or decrease quickly. Press the "Timer" key or
wait for the time display stop flashing to confirm the timer setting. Timer will start counting down after
timer setting.
●
If user want to turn off the timer, set the desired time to “00” or just hold “Timer” key for 3 seconds.
8
9
NOTE: After cooking, press “On/Off” key to switch off the unit. The hot indicator will keep lighting up
if the glass plate is over 60℃ to remind that the cooking plate is too hot to touch. The longest time that
the hot indicator keep lighting up can be 20 minutes.
NOTE: When the two burners work at the same time, the maximum power is 2800W.
When the power of induction zone is adjusted to b level (2800W), the infrared cooker has no
power output.
When the power of infrared zone is adjusted to level 9 (2800W), the induction cooker has no
actual power output.
Model
Voltage
Max. Output Power (W)
Unit Size (mm)
Unit Weight (kg)
Power adjustment range (W)
Glass panel dimension(mm)
Base cross-section dimension
GVI2800
220V~50Hz
2800W
735(L) x 415 (W) x 65 (H) (Dimension excluded stand)
735 (L) x 415 (W) x 95 (H) (Dimension included stand)
8.85
Left induction 600-2,800W
Right infrared 400 (single ring)-2,800W (double rings)
735 (L) x 415 (W)
670 (L) x 385 (W)
Heating principle of Ceramic Cooker
Considering the max.heat-resistant temperature of ceramic glass is only
750-800℃ and to avoid the ceramic glass would be broken caused by over
heated, the power rate will be decreased when the temperature of heating
plate reaches to approx. 710℃(±20℃) after heating approx. 1 minute, and the
power rate will keep heating continuously under stable range, the constant
temperature will keep at approx. 680℃(±20℃).
This heating program can make sure the ceramic glass’ using life time, and
continuous heating can avoid the water temperature changing too big to delay
the boiling time.
ating panel.
6) Do not use any flammable, acidic or alkaline materials or substances near the unit, as this may reduce
the service life of the unit and pose a fire risk when the unit is turned on.
7) In order to keep your cooker looking new, make sure that the bottom of your cookware does not scrape
the glass surface, although a scratched surface will not impair the use of the unit.
8) Make sure to properly clean the unit before storing it in a cool, dry place.
9) Cleaning and user maintenance shall not be made by children without supervision.
