Gillette SPH-120 Скачать руководство пользователя страница 3

PAGE 3 

THIS MANUAL CONTAINS IMPORTANT IN-
STRUCTIONS THAT MUST BE FOLLOWED DUR-

ING INSTALLATION, OPERATION, AND MAIN-
TENANCE OF THIS GENERATOR SET AND ALL 
ASSOCIATED EQUIPMENT.

 

 

Thoroughly read this operators manual before install-
ing, operating, or servicing your generator set.  Safe 
operation and best performance can be achieved 
only when this generator is operated and maintained 

properly. 
 

INTRODUCTION 

 
Thank you for your purchase of this 

SENTRY-PRO

 

automatic start/stop home standby generator set by 
GILLETTE GENERATORS, INC.  This generator set is 
intended for use as an alternative source of electric 

power to operate normally required household elec-
tric loads, during a utility power failure. 
 
This generator set has an all weather protected metal 
enclosure, 

MADE EXCLUSIVELY FOR OUTDOOR 

INSTALLATION

, and will operate on either vapor 

withdrawal liquid propane gas (LPG) or natural gas 
(NG).  

CAUTION:

 This generator does not comply 

with emergency power as defined in NFPA 70 of Na-
tional Electric Code. 
 

GILLETTE GENERATORS

 

has made every effort to 

present a modern, safe generator set that will give 
you a safe, clean supply of an alternative source.  

However, because each installation is different, it is 
impossible for this manual and GILLETTE to know and 
advise against all possible hazards.  The listings, 
warnings, and cautions in this manual and on tags and 

decals affixed to the generator set, are therefore, 

NOT ALL INCLUSIVE

.  If a certain procedure, work 

method, test method, or operating procedure is used, 
and is not recommended by GILLETTE, the person or 

company responsible for the generator modification, 
must assume all responsibility for safety and correct 
operation for the operator, service technician, and all 

others within generator area. 
 

READ YOUR GENERATOR SET MANUAL, PLUS 

SEPARATE ENGINE OPERATORS MANUAL AND 
AUTOMATIC TRANSFER SWITCH MANUAL 
CAREFULLY.  KNOW YOUR EQUIPMENT BE-

FORE YOU USE IT.  CONSIDER ANY POSSIBLE, 
POTENTIAL HAZARDS, BEFORE OPERATING 
YOUR GENERATOR SET. 
 

CAUTION: 

Only current licensed electrical and 

plumbing contractors should install your home 
standby generator.  All phase of installation must 
comply with all applicable local and national codes, 

industry standards, and regulations. 
 

THE GILLETTE WARRANTY IS AUTOMATICALLY 
NULL AND VOID WITHOUT THE USE OF LI-
CENSED ELECTRICIANS AND PLUMBERS, AND 

SO NOTED ON THE REGISTRATION FORM THAT 
IS TO BE RETURNED TO GILLETTE GENERA-
TORS, INC.

 

 

IMPORTANT SAFETY RULES 

 

The safety alert symbol

is used as a signal for 

possible danger, caution warning, or general hazard. 
 

DANGER:

 

Indicating a hazard that, if not avoided, 

will result in death or serious injury. 

 

WARNING:

 

Indicating a hazard that, if not 

avoided, could result in a death or serious injury. 
 

CAUTION:

 

Indicating a hazard that, if not avoided, 

might result in minor or moderate injury. 
 

NOTICE:

 

Indicating a hazard that, if not avoided, 

could result in general damage. 
 
Read and understand the above listed safety alert 
symbols, plus the following symbols that are used 

through out this manual. 
 
 

A LIST OF HAZARD SYMBOLS 

AND THEIR MEANINGS

 

SAVE THESE INSTRUCTIONS

 

Explosion 

Toxic Fumes 

Fire 

Chemical Burn 

Explosive Pressure 

Rotating Parts 

Hot Surface 

Electrical Shock 

Содержание SPH-120































Отзывы: