GILBARCO VEEDER-ROOT C00016 Series Скачать руководство пользователя страница 4

Страница: 4 / 34

Introduction

Page 4

MDE-4017G Mat Reader Assembly Kit (C00016-XXX) Installation Manual · April 2017

Abbreviations and Acronyms

Term

Description

ASC

Authorized Service Contractor

CRT

Cathode Ray Tube

EDH

Enhanced Dispenser Hub

e.i.r.p

Equivalent Isotropically Radiated Power

EMC

Electromagnetic Compatibility

ESD

Electrostatic Discharge

FCC

Federal Communications Commission

GOLD

Gilbarco

Online Documentation

Industry Canada

NEC

National Electrical Code

NFPA

National Fire Protection Association

p.i.r.e

Puissance Isotrope Rayonnée Équivalente

PCB

Printed Circuit Board

POS

Point of Sale

RSS

Radio Standards Specification

Underwriters Laboratories

USB

Universal Serial Bus

Required Reading

Before installation, the installer must read, understand, and follow:

• This manual.
• National Fire Protection Agency (NFPA) 30A, The Automotive and Marine Service

Station Code.

• NFPA 70

, The National Electrical Code (NEC).

• Applicable federal, state, and local codes and regulations.

Failure to do so may adversely affect the safe use and operation of the equipment.

Note: To ensure warranty, this kit must be installed by a Gilbarco-Authorized Service

Contractor (ASC). For assistance, call Gilbarco Help Desk at 1-800-800-7498.

Interconnect/Block Diagrams

Following table lists the Interconnect/Block Diagrams that are applicable for the kits:

Description

Part Number

Applicable Kit(s)

Interconnect/Block Diagram, Mat Reader

M01873 (Sheet 2)
M01873 (Sheet 3)

C00016-010
C00016-011

Notes: 1) The interconnect/block diagrams are shown in the appropriate kit

installation procedure.

2) Full-size drawings may also be available on Gilbarco Online

Documentation (GOLD) Library.

MDE-5255

EDH2 Passport Standalone Manager Workstation for PX60 Installation Poster

Passport

MDE-5351

Passport PIN Pad Stand Installation Instructions

Passport

Document
Number

Title

GOLD

Library

Содержание C00016 Series



































Результаты поиска

Содержание C00016 Series

Отзывы:

Похожие инструкции для C00016 Series

Бренды по названию

Популярные бренды

GILBARCO VEEDER-ROOT C00016 Series, Руководство по установке

Результаты поиска

Содержание C00016 Series

Отзывы:

Похожие инструкции для C00016 Series

Бренды по названию

Популярные бренды