manualshive.com logo in svg

Gigafast EE2400-G, Руководство пользователя

Поделиться
Скачать
Gigafast EE2400-G Скачать руководство пользователя страница 26

6. LED Indicators 

Before connecting any network device to EE2400-G Gigabit Ethernet Switch, 
you should take a few minutes to look over this chapter and get familiar with 
front panel LED indicators of your switch. The front-panel LED indicators of 
EE2400-G Gigabit Ethernet Switch comprise three sets of LEDs: System 
Status LEDs, Station Port LEDs and Gigabit Port LEDs. Each set of LEDs 
give specific information concerning either the Switch status or the port status:   
 

System LEDs 

System LEDs enable users to monitor the System Status. Power LED 
indicates the power on/off status of the switch. 
 

Station Port LEDs 

Station Port LEDs show the port status of each of its 24 10/100 Mbps station 
ports ( Link/Act, FDX/COL and 10/100 M status per port ). There are Link / Act 
( Link/Activity ), FDX/COL ( Full Duplex/Collision ) and 10/100 M LED to 
indicate its corresponding linking and transmission status.   
 

Gigabit Port LEDs 

Gigabit Port LEDs show the port status of the 2 Gigabit Ports. Link/Act LEDs 
and 100/1000M FDX LEDs indicate its corresponding linking and transmission 
status. 
 

 

 

System Status LEDs 

●

 Power LED 

    Power LED will give a solid green light when you turn on the Switch, and 

will be off when the Switch being turned off. You can simply check the 
Power LED status to see if the Switch is being activated or not. Before 
turning on the Switch, please verify that the power cord has been properly 
connected the Switch to the power outlet on the wall. 

 

●

 Link/Act LED 

Содержание EE2400-G































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды